AUMA ACExC 01.2 Intrusive Скачать руководство пользователя страница 58

Страница: 58 / 104

Press

Edit

➥

Display indicates:

▶ Specialist (4)

User login

Use

Up ▲ Down ▼

to select user:

Information: Required user level:

Specialist (4)

or higher

➥

The symbols have the following meaning:

black triangle:

▶

= current setting

white triangle:

▷

= selection (not saved yet)

Press

➥

Display indicates:

Password 0***

Enter password (

→

enter password).

➥

The screen indicates the pre-set type of seating (

▶Limit

▶Torque

) by means

of a black triangle

▶

Change settings

10. Use

Up ▲ Down ▼

to select new setting.

➥

The symbols have the following meaning:

black triangle:

▶

= current setting

white triangle:

▷

= selection (not saved yet)

11. Confirm selection via

Save

➥

The setting for the type of seating is complete.

12. Back to step 4 (CLOSED or OPEN): Press

Esc

10.2.

Open switch compartment

The switch compartment must be opened to perform the following settings.

Ignition of potentially explosive atmospheres caused by sparks!

Risk of death or serious injury!

→

Before opening the flameproof enclosure, ensure absence of gas and voltage.

→

Handle cover and housing parts with care.

→

Flameproof joints must neither be damaged nor soiled in any way.

→

Do not jam cover during fitting.

Loosen screws [2] and remove cover [1] from the switch compartment.

SAEx 07.2 – SAEx 16.2/SAREx 07.2 – SAREx 16.2 Control unit - electromechanical

Commissioning (basic settings)

ACExC 01.2 Intrusive Profinet

Содержание ACExC 01.2 Intrusive









































































































Результаты поиска

Содержание ACExC 01.2 Intrusive

Отзывы:

Бренды по названию

Популярные бренды

AUMA ACExC 01.2 Intrusive, Руководство по эксплуатации

Результаты поиска

Содержание ACExC 01.2 Intrusive

Отзывы:

Бренды по названию

Популярные бренды