manualshive.com logo in svg

AUMA ACExC 01.2 Intrusive, Руководство по эксплуатации

Поделиться
Скачать
AUMA ACExC 01.2 Intrusive Скачать руководство пользователя страница 62

3.

Press down and turn setting spindle [4] with screw driver in direction of the
arrow and observe the pointer [5]: While a ratchet click is felt and heard, the
pointer [5] moves 90° every time.

4.

As soon as the pointer [5] is 90° from mark [6]: Continue turning slowly.

5.

As soon as the pointer [5] moves to mark [6]: Stop turning and release setting
spindle.

➥

The intermediate position setting in running direction OPEN is complete.

6.

If you override the tripping point inadvertently (ratchet click is heard after the
pointer has snapped): Continue turning the setting spindle in the same direction
and repeat setting process.

10.6.

Test run

Only perform test run only once all settings previously described have been
performed.

The direction of rotation can be checked at the position indicator if available. (Chapter
<Direction of rotation at mechanical position indicator: check>)

The direction of rotation must be checked at the hollow shaft/stem if no mechanical
position indicator is available. (Chapter <Direction of rotation at hollow shaft/stem:
check>)

10.6.1.

Direction of rotation at mechanical position indicator: check

Valve damage due to incorrect direction of rotation!

→

If the direction of rotation is wrong, switch off immediately (press STOP).

→

Eliminate cause, i.e. correct phase sequence for cable set wall bracket.

→

Repeat test run.

Information

Switch off before reaching the end position.

1.

Move actuator manually to intermediate position or to sufficient distance from
end position.

2.

Switch on actuator in direction CLOSE and observe the direction of rotation on
the mechanical position indication:

→

For mechanical position indication via indicator mark: (not self-adjust-

ing)

➥

The direction of rotation is correct if the actuator operation in direction

CLOSE and the symbols (

/

) turn counterclockwise:

Figure 67: Direction of rotation 

/

 (for “clockwise closing version”)

62

SAEx 07.2 – SAEx 16.2/SAREx 07.2 – SAREx 16.2 Control unit - electromechanical

Commissioning (basic settings)

ACExC 01.2 Intrusive Profinet

Содержание ACExC 01.2 Intrusive









































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды