manualshive.com logo in svg

AUMA ACExC 01.2 Intrusive, Руководство по эксплуатации

Поделиться
Скачать
AUMA ACExC 01.2 Intrusive Скачать руководство пользователя страница 51

Table 27: Symbols along the pivot point axis

Stepping mode

Pivot point (intermediate position)
with operation profile

Symbol

End of stepping mode

Pivot point without reaction

|

Start of stepping mode in direction
CLOSE

Stop during operation in direction
CLOSE

Start of stepping mode in direction
OPEN

Stop during operation in direction
OPEN

–

Stop during operation in directions
OPEN and CLOSE

–

Pause for operation in direction CLOSE

–

Pause for operation in direction OPEN

–

Pause for operation in directions OPEN
and CLOSE

8.2.2.

Status indications according to AUMA classification

These indications are available if the parameter 

Diagnostic classific. M0539

 is set

to 

AUMA

.

Warnings (S0005)

If a warning has occurred, the display shows 

S0005

:

●

the number of warnings occurred

●

a blinking question mark after approx. 3 seconds

Figure 55: Warnings

For further information, please also refer to <Corrective action>.

Not ready REMOTE (S0006)

The 

S0006

 display shows indications of the Not ready REMOTE group.

If such an indication has occurred, the display shows 

S0006

:

●

the number of indications occurred

●

a blinking crossbar after approx. 3 seconds

Figure 56: Not ready REMOTE indications

For further information, please also refer to <Corrective action>.

Fault (S0007)

Once a fault has occurred, the 

S0007

 display shows:

●

the number of faults occurred

●

a blinking exclamation mark after approx. 3 seconds

51

SAEx 07.2 – SAEx 16.2/SAREx 07.2 – SAREx 16.2 Control unit - electromechanical
ACExC 01.2 Intrusive Profinet

Indications

Содержание ACExC 01.2 Intrusive









































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды