manualshive.com logo in svg

AUMA ACExC 01.2 Intrusive, Руководство по эксплуатации

Поделиться
Скачать
AUMA ACExC 01.2 Intrusive Скачать руководство пользователя страница 23

5.3.3.1. Multi-turn actuator with output drive type B: mount

Figure 18: Mounting output drive types B

[1]

Multi-turn actuator

[2]

Valve/gearbox

[3]

Valve/gearbox shaft

Procedure

1.

Check if mounting flanges fit together.

2.

Check if output drive of multi-turn actuator [1] matches the output drive of
valve/gearbox or valve/gearbox valve shaft [2/3].

3.

Apply a small quantity of grease to the valve or gearbox shaft [3].

4.

Place multi-turn actuator [1] and ensure that the spigot fits uniformly in the recess
and that the mounting faces are in complete contact.

5.

Fasten multi-turn actuator with screws according to table.

Information: We recommend applying liquid thread sealing material to the
screws to avoid contact corrosion.

6.

Fasten screws crosswise to a torque according to table.

Table 13:

Tightening torques for screws

Tightening torque [Nm]

Threads

Strength class A2-80/A4–80

24

M8

48

M10

200

M16

392

M20

23

SAEx 07.2 – SAEx 16.2/SAREx 07.2 – SAREx 16.2 Control unit - electromechanical
ACExC 01.2 Intrusive Profinet

Assembly

Содержание ACExC 01.2 Intrusive









































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды