Atlas Copco 4045HFG81 Скачать руководство пользователя страница 17

Страница: 17 / 136

- 17 -

2.2

Markings

Markings provide instructions and information. They
also warn of hazards. For convenience and safety,
keep all markings in legible condition, replacing them
when damaged or missing. Replacement markings are
available from the factory.
A brief description of all markings provided on the
generator set is given hereafter. The precise location
of all markings can be found in the parts manual of
this generator set.

Indicates the presence of electric shock
hazards. Enclosures marked with these
symbols should only be opened by
trained or instructed people.

Indicates that these parts can become
very hot during operation (e.g. engine,
cooler, etc.). Always make sure that
these parts are cooled down before
touching them.

Indicates the sound power level in
accordance with Directive 2000/14/
EC (expressed in dB (A)).

Indicates that the generator set may be
refuelled with diesel fuel only.

Indicates the drain for the engine oil.

diesel

Indicates the drain for the coolant.

Indicates the drain plug for the engine
fuel.

Use PAROIL E only.

Indicates that the alternator should not
be cleaned with high pressurised
water.

Indicates the battery switch.

Indicates that the unit may
start automatically and that
the instruction book has to
be consulted prior to use.

Read the instruction manual
before using the lifting eye.

Indicates the 3-way valve.

Indicates the different
service packs, liquids and
critical parts. These parts
can be ordered to Atlas
Copco.

QES XXX

Engine XXXXXXXX

Fuel tank capacity

XXX L.

Oil sump capacity XXX L.

Cool. system capacity XXX L.

Alternator XXXXXXXXXXX

Service Pak

Description Order

SERVICE PACK 500 HOURS

xxxxxxxxxxx

SERVICE PACK 1000 HOURS

xxxxxxxxxxx

SERVICE PACK 2000 HOURS

xxxxxxxxxxx

Fluids

Description Order

PAROIL E 5L (1.1GAL)

xxxxxxxxxxx

PAROIL E 20L (4.4GAL)

xxxxxxxxxxx

PAROIL E 209L (45.98GAL)

xxxxxxxxxxx

PAROIL E XTRA 5L (1.1GAL)

xxxxxxxxxxx

PAROIL E XTRA 20L (4.4GAL)

xxxxxxxxxxx

PARCOOL EG 5L (1.1GAL)

xxxxxxxxxxx

PARCOOL EG 20L (4.4GAL)

xxxxxxxxxxx

PARCOOL EG CONCENTRATE 5L (1.1GAL)

xxxxxxxxxxx

Alternator Parts

Description Order

TERMINAL BOARD

xxxxxxxxxxx

EXCITOR STATOR

xxxxxxxxxxx

EXCITER ROTOR

xxxxxxxxxxx

DIODE BRIDGE

xxxxxxxxxxx

COOLING FAN

xxxxxxxxxxx

DSR

xxxxxxxxxxx

FRONT BEARING

xxxxxxxxxxx

REAR BEARING

xxxxxxxxxxx

Engine Parts

Description Order

OIL FILTER KIT

xxxxxxxxxxx

SAFETY CARTRIDGE

xxxxxxxxxxx

AIR FILTER ELEMENT

xxxxxxxxxxx

FUEL FILTER WS

xxxxxxxxxxx

SEAL KIT

xxxxxxxxxxx

FUEL FILTER

xxxxxxxxxxx

ROCKER COVER GASKET

xxxxxxxxxxx

V-BELT

xxxxxxxxxxx

LIFT FUEL PUMP

xxxxxxxxxxx

STARTER MOTOR

xxxxxxxxxxx

DIPSTICK

xxxxxxxxxxx

OIL FILLER CAP

xxxxxxxxxxx

ENGINE ALTERNATOR

xxxxxxxxxxx

COOLANT TEMP. SENSOR

xxxxxxxxxxx

OIL PRESSURE SENSOR

xxxxxxxxxxx

FUEL PRESSURE SENSOR

xxxxxxxxxxx

MAGNETIC PICK UP

xxxxxxxxxxx

AIR TEMPERATURE SENSOR

xxxxxxxxxxx

WS FILTER SENSOR

xxxxxxxxxxx

RADIATOR HOSES KIT

xxxxxxxxxxx

COOLANT LEVEL SWITCH

xxxxxxxxxxx

RADIATOR CAP

xxxxxxxxxxx

CRANKCASE VENT FILTER ELEM

xxxxxxxxxxx

RADIATOR KIT

xxxxxxxxxxx

FUEL TANK CAP Ø80 WITH KEY

xxxxxxxxxxx

Keys

Description Order

FUEL TANK CAP KEYS

xxxxxxxxxxx

DOOR KEYS

xxxxxxxxxxx

1636008952

www.atlascopco.com

Содержание 4045HFG81









































































































































Результаты поиска

Содержание 4045HFG81

Отзывы:

Похожие инструкции для 4045HFG81

Бренды по названию

Популярные бренды

Atlas Copco 4045HFG81, Инструкция по эксплуатации

Результаты поиска

Содержание 4045HFG81

Отзывы:

Похожие инструкции для 4045HFG81

Бренды по названию

Популярные бренды