AstroJet M1DX Скачать руководство пользователя

Страница: 84 / 97

SECTION 5
TROUBLESHOOTING

Errors and Warnings

Printer Alert Window Messages

Messages sent from Driver and displayed on PC screen in a small
popup window.

MESSAGE

SOLUTION

Cleaning in Progress

Wait until message disappears. Printer will start printing your job once
cleaning process is complete.

Excessive Tilt Error

See details under

“Toolbox System Status Messages”

section.

Incompatible
Printhead

Remove and reinsert your Printhead Cartridge. Replace Printhead. Printhead
Cartridges must be purchased from authorized supplier for this printer model.

Incorrect … Ink Tank

Replace Ink Tank. Ink Tanks must be purchased from authorized supplier for
this printer model.

…. Ink Low

Example: Black Ink Low

Reorder Ink.

…. Out of Ink

Example: Cyan Ink Out

Replace empty Ink Tank.

Load Paper

Out of Paper. Load media into Printer and press

PAPER

button to

resume printing.

Mechanical Jam

Check for and remove obstruction, then press

PAPER

button to

resume printing.
Check/Clean Sensors. If problem persists, contact technical support.

Missing Printhead

Remove Printhead Cartridge. Check/clean electrical contacts. Reinsert
Printhead. Replace Printhead. If problem persists, contact technical support.

Multiple Inks Low

Reorder Ink.

Multiple Ink Tanks
Out

Replace empty Ink Tanks.

Multiple Ink Tanks are
missing

Insert missing Ink Tanks.
Clean electrical contacts and reseat Ink Tanks.

Multiple Unauthorized
Ink Tanks

Remove and reinsert Ink Tank. Replace Ink Tank. Ink Tanks must be
purchased from authorized supplier for this printer model.

Paper Jam

Remove jammed media. Check for proper feed setup then press

PAPER

button to resume printing.
Check/Clean Sensors. If problem persists, contact technical support.

Printhead Latch Open

Ensure that Printhead Cartridge is inserted properly, then close Printhead
Latch so it locks.

Print Zone Assembly
(Clamshell) Open

Check to be sure Clamshell is completely closed and latched.
Make sure Print Engine Latches are secure.

The … Ink Tank is
missing

Insert missing Ink Tank.
Clean electrical contacts and reseat Ink Tank.

Unauthorized … Ink
Tank Installed

Ink Tanks must be purchased from authorized supplier for this printer model.

Unauthorized
Printhead

Printhead Cartridges must be purchased from authorized supplier for this
printer model.

Содержание M1DX

































































































Результаты поиска

Содержание M1DX

Отзывы:

Похожие инструкции для M1DX

Бренды по названию

Популярные бренды

AstroJet M1DX, Руководство оператора

Результаты поиска

Содержание M1DX

Отзывы:

Похожие инструкции для M1DX

Бренды по названию

Популярные бренды