Asco 230 Series Скачать руководство пользователя страница 18

Страница: 18 / 32

14 Chapter 3 Operation

Series 230 Automatic Transfer Switch C2000 Intelligent Controller User Manual

Chapter 3 Operation

3.1 Operation Panel

There is a LCD display screen, LED Indicators and operation keys on the Controller operation panel, as shown in Fig.

3-1.

Operation

Status Indicator

Mode

Indicator

Alarm

Indicator

Display

Key Pad

Source II Available

Indicator

Source I Available

Indicator

Source I Accepted

Indicator

Source II Accepted

Indicator

Center-off Position

Indicator

Figure 3-1 Operation Panel

The Indicator descriptions are shown in Table 3-1.

Table 3-1 Indicator Description

Indicator

Description

Operation Status Indicator

(green)

This light indicate the operating status of the Controller. When it is on, it indicates normal

operation; and when it is off, it indicates abnormal operation.

Mode Indicator

(green)

When it is on, it indicates that the Controller is running in auto mode. When it blinks slowly it

indicates that the Controller is running in manual mode. When it blinks rapidly it indicates

that the Controller is running in remote mode.

Alarm Indicator

(red)

When in Source I Priority Mode, the alarm indicator will be on when the Controller detects

such abnormalities as under-voltage, overvoltage, phase loss and power failure on Source I.

It ignores the status of Source II.

When in the No-Source Priority Mode or the Remote Mode, the alarm will be on when the

Controller detects such abnormalities as under-voltage, overvoltage, phase loss and power

failure on Source I and Source II.

Otherwise, the alarm will flash during any critical failure, such as switch operation failure or

fire alarm.

Source I Available Indicator

(green)

When it is on, it indicates normal operation of Source I. When it is off, it indicates that Source I

is not connected or loss of power.

Source II Available Indicator

(green)

When it is on, it indicates normal operation of Source II. When it is off, it indicates that Source

II is not connected or loss of power.

Source I Accepted Indicator

(green)

When it is on, it indicates that Source I is connected. When it is off, it indicates that Source I

is in the process of switching off or not connected.

Source II Accepted Indicator

(green)

When it is on, it indicates that Source II is connected. When it is off, it indicates that Source

II is in the process of switching off or not connected.

Center-off Position Indicator

(yellow)

When it is on, it indicates that the load is in OFF status. When it is off, it indicates that the load

is not in OFF status and it is supplied by either Source I or Source II.

Содержание 230 Series

































Результаты поиска

Содержание 230 Series

Отзывы:

Бренды по названию

Популярные бренды

Asco 230 Series, Руководство пользователя

Результаты поиска

Содержание 230 Series

Отзывы:

Бренды по названию

Популярные бренды