Arturia MICROFREAK Скачать руководство пользователя

Страница: 21 / 104

3.1.3.4. LFO

An LFO is a low-frequency oscillator that can produce various waveforms at sub-audio

frequencies (0.05Hz up to 100Hz). The MicroFreak provides one LFO with six waveforms.

You select a waveform with the Shape button: sine, triangle, rising sawtooth, square, random

stepped (also referred to as sample & hold), and random gliding (or smoothed random).

• Sine rises and falls between its minimum and maximum values
• Triangle rises and falls in more of a linear way between its minimum and

maximum values

• Sawtooth rises linearly to its maximum value and then drops suddenly to its

minimum value

• Square rises and falls suddenly between its minimum and maximum values
• Random stepped rises and falls suddenly between values that are generated at

random

• Random gliding rises and falls gradually between values that are generated at

random

The Rate control knob doubles as a Sync switch. When you press it, the Sync LED will light

up to indicate that LFO Sync is activated. In synced mode the LFO rate is slaved to the

Sequencer/Arpeggiator tempo clock (Seq). In unsynced mode the LFO rate depends solely

on the Rate knob setting.

3.1.3.5. The General Envelope Generator

The Envelope Generator is one of the basic building blocks of MicroFreak. It enables you

to shape the overall loudness of a tone or the timbre of a sound. It's a sound sculpting

tool. It can be patched to all destinations on the Matrix, including the destinations you

create yourself. The first three knobs - Attack, Decay/Release, and Sustain - affect the Filter

by default. The last knob, Filter Amt, enables you to set the amount by which the Filter

will be affected by the Envelope. Their functions are described extensively in the

Envelope

Generator [p.52]

chapter.

When the Amp Mod switch is active, the Envelope will also affect the loudness of the VCA

and thus shape the overall loudness of the MicroFreak.

The LFO

The Envelope Generator

Arturia - User Manual MicroFreak - MicroFreak Overview

Содержание MICROFREAK









































































































Результаты поиска

Содержание MICROFREAK

Отзывы:

Похожие инструкции для MICROFREAK

Бренды по названию

Популярные бренды

Arturia MICROFREAK, Руководство пользователя

Результаты поиска

Содержание MICROFREAK

Отзывы:

Похожие инструкции для MICROFREAK

Бренды по названию

Популярные бренды