Arturia MICROFREAK Скачать руководство пользователя страница 25

Страница: 25 / 104

3.2.6. Power switch

If you want to turn the unit off without disconnecting the USB cable, use this recessed

switch. The power switch toggles between OFF and USB power / DC power. When both are

connected, DC is used. If you plug in DC power the MicroFreak will reset.

Note:

The power requirements of the MicroFreak are so low that you can power it with the

same power bank you use to recharge your phone or tablet when you're in a place without

power outlets.

3.2.7. Power Connector

The power connector connects the MicroFreak to the mains outlet. Please only use the Power

Supply provided by Arturia.

It was designed specifically to provide the ground needed for the capacitive keyboard to

operate properly.

The On/Off switch

The power connector

Arturia - User Manual MicroFreak - MicroFreak Overview

Содержание MICROFREAK









































































































Результаты поиска

Содержание MICROFREAK

Отзывы:

Бренды по названию

Популярные бренды

Arturia MICROFREAK, Руководство пользователя

Результаты поиска

Содержание MICROFREAK

Отзывы:

Бренды по названию

Популярные бренды