Arturia MICROFREAK Скачать руководство пользователя страница 82

Страница: 82 / 104

13.2. The Modulation Tracks

Without a doubt, the most exciting feature of the Sequencer are its four modulation tracks.

A sequence pattern record notes (the pitch of a note) and velocities (the strength with which

you hit the key); modulation tracks record knob positions.

In Step-recording mode the modulation tracks enable you to take snapshots of knobs and

record these snapshots along with a sequencer step. Recording on a modulation track is a

two-step process: first, you record a sequence in the standard track, and when done you fill

the modulation tracks.

Note:

When recording in Step mode, pressure data isn't saved with the Preset since it can't

be recorded in Step-recording mode or edited.

There are as many modulation steps as there are sequencer steps. In a track you can store

the states of only one specific knob. As there are four tracks you can store the values of four

knobs, up to 64 values for each knob.

Note:

The actual number of values you can store depends on the length of the sequence.

You can store 16 values in a 16 step sequence and 64 in a 64 step sequence.

Note:

Note and Modulation recording can happen simultaneously; hold the notes and turn

the knobs.

13.2.1. Step-time recording of modulation

To record modulation in step time:

• Select the sequence into which you want to record events.

• Make certain "play" is off and turn on step recording by pushing the record

button.

• Turn the Sequencer Rate knob until you are on the first step of the sequence, or

select another step in the sequence if that's where you want to add events.

• Now turn a knob you want to record. While turning the knob nothing will be

recorded, but you monitor what is happening. Once you've found a knob position

that you want to record, let go of the knob. MicroFreak will take a snapshot of the

knob and store it with the step.

• Turn the Sequence Rate knob to the next step and move the same knob to

another position you want to record. Continue to do this until you've filled every

step with a snapshot.

Note:

When you try to record the activity of a fifth knob the display will flash a message

saying "Memory full".

If you touch a knob when in step recording mode, that button will automatically be assigned

to the first available modulation track. When starting with a new sequence that will be

modulation track one. Touch another knob, and it will be assigned to the next available

modulation track. You may have guessed by now that there are two ways to fill modulation

tracks: you can fill a track and then continue to the next track taking snapshots of another

knob, or you fill a step and record four knob positions simultaneously and then continue to

the next step until all steps are full. Both methods have their pros and cons.

Arturia - User Manual MicroFreak - The Sequencer

Содержание MICROFREAK









































































































Результаты поиска

Содержание MICROFREAK

Отзывы:

Бренды по названию

Популярные бренды

Arturia MICROFREAK, Руководство пользователя

Результаты поиска

Содержание MICROFREAK

Отзывы:

Бренды по названию

Популярные бренды