Artistic Licence Commissioner rdmx Скачать руководство пользователя страница 45

Страница: 45 / 47

Glossary

Channel

There are a maximum of 512 channels in a DMX packet. This term is identical to Data slot. Channels
number from 1

–

512.

Slot

Slot refers to the 513 bytes that can be contained in a DMX frame. Slots number from 0

–

512, zero

being the start code.

Data slot

Data slot is the formal name for Channel.

Footprint

The number of channels or data slots that a DMX receiver uses.

Personality

Personalities allow RDM devices to have different setups that can be selected via RDM.

RDM

Remote Device Management.

Refresh rate

This repeat rate of DMX512 data. The maximum refresh rate of DMX with a full 512 channel payload
is 44Hz.

Get

The RDM term meaning to read a parameter.

Set

The RDM term meaning to programme a parameter.

ISD

The delay between DMX slots.

Содержание Commissioner rdmx
















































Результаты поиска

Содержание Commissioner rdmx

Отзывы:

Похожие инструкции для Commissioner rdmx

Бренды по названию

Популярные бренды

Artistic Licence Commissioner rdmx, Руководство пользователя

Результаты поиска

Содержание Commissioner rdmx

Отзывы:

Похожие инструкции для Commissioner rdmx

Бренды по названию

Популярные бренды