Artistic Licence Commissioner rdmx Скачать руководство пользователя страница 11

Страница: 11 / 47

DMX512 Menu

The DMX512 menu categorises all the available DMX512 and RDM functions as listed below. Use the
RIGHT key to access the relevant sub-menus.

The DMX sub-menus are:

TRANSMIT

Transmit test patterns of DMX to dimmers or fixtures.

RECEIVE

Receive and view DMX levels plus analyse timing.

RDM

Discover, configure and monitor RDM devices.

ADVANCED

Test the DMX network, fix bad DMX and access our unique discombobulator.

CABLE

Test connectivity of the three DMX conductors.

DMX - TRANSMIT Menu

The DMX-TRANSMIT menu provides five options. Use UP and DOWN to navigate and then press
ENTER.

The sub-menus are:

CHANNEL

Transmit a single channel at a level.

RANGE

Transmit a range of channels at a level or changing levels.

SCENE

Playback one of forty recorded scenes.

SNAPSHOT

Snapshot (record from received DMX) into any of the forty scenes.

CONFIG

Setup numerous timing parameters for transmitted DMX.

DMX - TRANSMIT - CHANNEL Menu

This menu allows transmission of a single channel (aka data slot) of DMX at any level.

Keys operate as follows:

LEFT

and

RIGHT

Navigate through the option fields. In the product, option fields are shown in

UPPER CASE. In this guide, option fields are highlighted in red.

and

DOWN

Select the required value within an option field.

DMX MENU

TRANSMIT

RDM

DMX512 TX

<CHANNEL

RANGE

Содержание Commissioner rdmx
















































Результаты поиска

Содержание Commissioner rdmx

Отзывы:

Похожие инструкции для Commissioner rdmx

Бренды по названию

Популярные бренды

Artistic Licence Commissioner rdmx, Руководство пользователя

Результаты поиска

Содержание Commissioner rdmx

Отзывы:

Похожие инструкции для Commissioner rdmx

Бренды по названию

Популярные бренды