Arjo Enterprise E8000X Скачать руководство пользователя | Manualshive

Страница: 9 / 105

background image

Enterprise E8000X Service Manual

Decontamination

Page 5

CHAPTER 2

DECONTAMINATION

1

Cleaning

Wearing suitable protective clothing, clean all surfaces with a disposable cloth soaked in a neutral
detergent and hand hot water.

The mattress platform sheets and head/foot boards can be removed from the bed and cleaned
separately.

Start by cleaning the upper sections of the bed and work along all horizontal surfaces. Work methodically
towards the lower sections of the bed and clean the castors last. Take extra care to clean areas that may
trap dust or dirt.

Wipe over with a new disposable cloth moistened with clean water and dry with disposable paper towels.

Allow the cleaned parts to dry before replacing the mattress.

2

Disinfecting

After cleaning the bed as described above, wipe all surfaces with sodium dichloroisocyanurate (NaDCC)
at a concentration of 1,000 parts per million (0.1%) of available chlorine.

In the case of pooling body fluids, e.g. blood, the concentration of NaDCC should be increased to 10,000
parts per million (1%) of available chlorine.

WARNING

Disconnect the bed from the mains power supply before carrying out cleaning
procedures.
Do not allow the mains plug or power supply cord to get wet when cleaning
the bed.

Caution

Do not use abrasive compounds or pads or phenol-based disinfectant
solutions.
Do not use jet stream cleaning or wash tunnels.
Take care not to remove grease from the actuator pistons.

«
...
7
8
9
10
11
...
»

Содержание Enterprise E8000X










































































































Отзывы:

Нет отзывов

Похожие инструкции для Enterprise E8000X

Бренд: XTA Страницы: 29

Бренд: vc999 Страницы: 59

Бренд: Qtx Страницы: 3

Бренд: Saferoad Страницы: 24

D-IMager EKL3104

Бренд: Panasonic Страницы: 13

Бренд: Labokey Страницы: 5

Бренд: E-Z Trail Страницы: 8

Бренд: B&K Страницы: 10

Бренд: Raytech Страницы: 21

Бренд: Teac Страницы: 2

Бренд: laerdal Страницы: 2

Бренд: Bard Страницы: 36

Бренд: Bard Страницы: 2

Бренд: Bard Страницы: 30

Бренд: Bard Peripheral Vascular Страницы: 44

Бренд: Rain-Flo Irrigation Страницы: 16

Sportsound SSR-200

Бренд: Daktronics Страницы: 5

Бренд: Gainsborough Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды