Arjo Enterprise E8000X Скачать руководство пользователя

Страница: 15 / 105

Enterprise E8000X Service Manual

Troubleshooting

Page 11

CHAPTER 5

TROUBLESHOOTING

Fault finding

The following table identifies some fault symptoms, possible cause(s) and suggested remedial action.

Fault Indications

The bed’s control software can detect and indicate faults within the electrical system by means of
flashing LEDs on the Attendant Control Panel (ACP). These fault codes are shown in the following table.

Symptom

Possible cause

Remedial action

All actuators inoperative

Functions locked on ACP

Unlock functions on ACP

Power disconnected and
backup battery
discharged

Connect the power supply cord to a
suitable outlet socket

Mains fuse blown and
backup battery
discharged

Check fuse in mains plug (UK BS1363
type plug only)

Patient / nurse controls
disconnected

Check wiring between head end split
side rails, junction box and control box

ACP disconnected

Check wiring between foot end split
side rails, junction box and control box

One actuator
inoperative.

Actuator cable
disconnected or faulty.

Check actuator cable is plugged into
both the control box and the
actuator. Check actuator cable.

All functions inoperative,
except raising the mattress
platform.

Control box software has
lost calibration.

Raise mattress platform to maximum
height and flatten all sections to reset
the software.

Brakes and/or steering lock
not effective.

Worn or damaged
castor(s) or brake pedal.

Replace castor(s) or brake pedal.

Emergency CPR release
inoperative.

CPR release cable(s)
stretched or worn.

Adjust or replace CPR
release cable(s).

ACP LED(s) flashing

ACP LED(s)
always on

Fault location

Height actuator on control unit Channel 2 (drives
foot end radius arm)

Height actuator on control unit Channel 4 (drives
head end radius arm)

Содержание Enterprise E8000X










































































































Результаты поиска

Содержание Enterprise E8000X

Отзывы:

Похожие инструкции для Enterprise E8000X

Бренды по названию

Популярные бренды

Arjo Enterprise E8000X, Руководство по обслуживанию

Результаты поиска

Содержание Enterprise E8000X

Отзывы:

Похожие инструкции для Enterprise E8000X

Бренды по названию

Популярные бренды