Arjo Enterprise 9600X Скачать руководство пользователя

Страница: 68 / 76

Scales rating

Class III

Dimensions

(subject to normal manufacturing tolerances

)

Overall length

Position 1 (Short)

210 cm (86.2 ins.)

Position 2 (Standard)

230cm (90.6 ins.)

Position 3 (Extended)

242 cm (95.3 ins.)

In-bed length

Position 1 (Short)

192cm (75.6 ins.)

Position 2 (Standard)

203cm (79.9 ins.)

Position 3 (Extended)

215cm (84.6 ins.)

Overall width

103cm (40.6 ins.)

Height of mattress platform (centre of seat section to floor)

With 125mm castors

32cm to 76cm (12.6 to 29.9 ins.) Curved
Deck Sheets
34cm to 78cm (13.3 to 30.7 ins)
Flat Deck Sheets

With 150mm castors

34cm to 78cm (13.3 to 30.7 ins.) Curved
Deck Sheets
36cm to 80cm (14.1 to 31.5 ins.)
Flat Deck Sheets

Head down tilt angle

12° min.

Foot down tilt angle

12° min.

Mattress size (refer to the section “Mattresses” on page 17)

Position 2 (Standard)

202cm x 88cm, 12.5 to 18cm thick (79.5
ins. x 34.6 ins, 5 to 7 ins. thick)

Mattress platform angles

Содержание Enterprise 9600X













































































Результаты поиска

Содержание Enterprise 9600X

Отзывы:

Похожие инструкции для Enterprise 9600X

Бренды по названию

Популярные бренды

Arjo Enterprise 9600X, Инструкция по эксплуатации

Результаты поиска

Содержание Enterprise 9600X

Отзывы:

Похожие инструкции для Enterprise 9600X

Бренды по названию

Популярные бренды