Arjo Enterprise 9600X Скачать руководство пользователя | Manualshive

Страница: 12 / 76

background image

12

3. Installation

The following chapter describes how to install the bed.

WARNING

If the power supply cord or plug is damaged, the complete assembly
must be replaced by authorised service personnel. Do not remove the
fitted plug, or use a rewireable plug or adapter.
Make sure the power supply cord is not stretched, kinked or crushed.
Do not allow the power supply cord to trail on the floor where it may
cause a trip hazard.
Make sure the power supply cord does not become entangled with
moving parts of the bed or trapped between the bed frame and head
board.
Disconnect the power supply cord from the electricity supply, and
store it as shown, before moving the bed.
Before the first use, or if the bed has been unused for more than three
months, read and understand this IFU and test the functionality of the
bed to verify correct operation. Refer to “Preventive maintenance” on
page 58 for a list of functional tests.

Caution

Before the first use, or if the bed has been unused for more than three
months, connect the bed to the electricity supply for at least 24 hours
to allow the backup battery to recharge fully; failure to do this may
reduce the life of the battery. After charging, check that the battery is
fully serviceable by carrying out a battery test as shown on page 61.

«
...
10
11
12
13
14
...
»

Содержание Enterprise 9600X













































































Отзывы:

Нет отзывов

Похожие инструкции для Enterprise 9600X

Бренд: Walker Bay Страницы: 8

Бренд: UNIA Страницы: 62

Бренд: B&G Страницы: 3

Бренд: Raven Страницы: 12

Бренд: Zero 88 Страницы: 20

Бренд: Kapriol Страницы: 32

Бренд: Cabletron Systems Страницы: 33

Бренд: i-CAT Страницы: 32

Бренд: Eaton Страницы: 21

Бренд: NANO Страницы: 4

Бренд: NEILPRYDE Страницы: 55

Бренд: HANYOUNGNUX Страницы: 4

Бренд: Park House Healthcare Страницы: 6

Бренд: J&M Страницы: 33

Бренд: Vahterus Страницы: 31

Бренд: XanLite Страницы: 4

Бренд: Wang Страницы: 146

Бренд: Major tech Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды