Arjo Enterprise 9600X Скачать руководство пользователя

Страница: 51 / 76

SafeSet™

SafeSet

visual status indicators provide a quick visual

indication of optimum bed settings for patients identified as
being at risk of falls.

SafeSet

visual status indicators show four safety-critical bed

parameters:

• Brake setting
• Side rail position
• Mattress platform height
• Movement detection status.

Two identical

SafeSet

indicator panels are located just below

the foot board.
Indicator lights (

) above each symbol light red to show a

potentially unsafe condition, or green to indicate a safe
condition.

Fig. 31 -

SafeSet

indicator panel

* To comply with FDA guidelines, the system will still show a “safe” condition if one (but not both) of the
foot end side rails are down.

WARNING

SafeSet

visual status indicators are only for use with patients at risk

of falls and should not be used with patients that are at risk of
climbing over the side rails.

Symbol

Indicator light green

(“safe” condition)

Indicator light red

(“unsafe” condition)

Brakes on

Brakes off

All side rails raised*

If either of the head end panels are
lowered.
If both foot end panels are lowered.

Mattress platform at
minimum height (or within
25mm of minimum height)

Mattress platform not at minimum height

VariZone patient movement
detection set

VariZone patient movement detection not
set

Содержание Enterprise 9600X













































































Результаты поиска

Содержание Enterprise 9600X

Отзывы:

Похожие инструкции для Enterprise 9600X

Бренды по названию

Популярные бренды

Arjo Enterprise 9600X, Инструкция по эксплуатации

Результаты поиска

Содержание Enterprise 9600X

Отзывы:

Похожие инструкции для Enterprise 9600X

Бренды по названию

Популярные бренды