Arjo Enterprise 9600X Скачать руководство пользователя | Manualshive

Страница: 63 / 76

background image

63

Error code E410 and
flashing control panel
lights

Flat battery

If the bed has just been
delivered or has been
left in storage for a long
period of time without
charge, plug the bed
into mains power and
leave to charge as per
instructions.
If the problem persists
call an Arjo approved
service engineer

Alarm sounds when
patient moves on the bed

Movement detection
threshold set too low

Increase VariZone patient
movement detection
threshold setting

Errors in indicated patient
weight

Mattress platform
obstructed

Check the mattress
platform is not touching
furniture, curtains, cables,
etc.
Check that weight has not
been added to the bed
without using the auto-
compensation function.

Nurse call function not
working

Nurse call cable not
connected or wrong type

Check cable is of correct
type and properly
connected

Backrest does not lower
using the manual CPR
release handle

Insufficient patient weight
applied to the backrest

Push the backrest down to
initiate lowering

Error code E001

Zero on battery power

Connect bed to mains

supply and re-initialise

the weighing system -

see page 45

Error code E002

Auto Compensation
weight decrease more
than 100kg (220 lb.)

Replace weight removed
from bed

Error code E003

Auto Compensation
weight increase more than
100kg (220 lb.)

Remove added weight
from bed

Error code E102

A stable weight reading
was not obtained within 10
seconds

Refer to the points listed

in the section

“Accuracy” on page 44

Symptom

Possible Cause

Action

«
...
61
62
63
64
65
...
»

Содержание Enterprise 9600X













































































Отзывы:

Нет отзывов

Похожие инструкции для Enterprise 9600X

Бренд: Nemco Страницы: 13

Бренд: Ecco Страницы: 12

Бренд: UMF Medical Страницы: 12

Бренд: DBX Bushido Страницы: 12

Бренд: Garelick Страницы: 2

Бренд: Garelick Страницы: 2

Бренд: Mackie Страницы: 18

Бренд: Mackie Страницы: 2

Бренд: Mackie Страницы: 8

Бренд: Mackie Страницы: 7

Бренд: Kärcher Страницы: 148

Exitronix LEMD Series

Бренд: BARRON Страницы: 6

Бренд: EFX Страницы: 2

NTP TECHNOLOGY DAD Thunder Core 256

Бренд: DAN Страницы: 16

Бренд: Lencarta Страницы: 6

Бренд: Cablexpert Страницы: 12

Бренд: ESD Страницы: 26

Бренд: Sulky Страницы: 99

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды