Ariterm Arimatic 151 Скачать руководство пользователя страница 37

Страница: 37 / 43

v2.00

Ariterm Oy

21.5.2013

performs a cleaning movement, where the linear actuator moves from one end
to the other.

The grate pulses (running and pause time) is determined for five power points
which the programme uses for calculating times for other power levels.

17.7 Shunt control (Heating circuit control)

Figure 24. SHUNT CONTROL -settings.

Setting

Factory
setting

Setting
frequenc
y

Function

Water temperature

True
value

Supply water temperature

Water temperature

35°C

0-100°C

Supply water temperature setting when
shunt control is in the NOT IN USE mode.

Water temperature
sensor scaling min.

-10°C

-
150…15
0°C

Supply water temperature sensor scaling
NOTE! Requires Maintenance level
password.

Water temperature
sensor scaling max.

150°C

-
150…15
0°C

Supply water temperature sensor scaling
NOTE! Requires Maintenance level
password.

Out temperature

True
value

Outdoor temperature.

Out temperature
sensor scaling
min.

-50°C

-
150…15
0°C

Outdoor temperature sensor scaling.
NOTE! Requires Maintenance level
password.

Outdoor
temperature sensor
scaling max.

50°C

-
150…15
0°C

Outdoor temperature sensor scaling.
NOTE! Requires Maintenance level
password.

Содержание Arimatic 151












































Результаты поиска

Содержание Arimatic 151

Отзывы:

Бренды по названию

Популярные бренды

Ariterm Arimatic 151, Руководство пользователя

Результаты поиска

Содержание Arimatic 151

Отзывы:

Бренды по названию

Популярные бренды