manualshive.com logo in svg

Ariterm Arimatic 151, Руководство пользователя

Поделиться
Скачать
Ariterm Arimatic 151 Скачать руководство пользователя страница 19

v2.00 

Ariterm Oy 

21.5.2013 

18 

 

Then, the burner screw feeds fuel to the 
burner head for the duration of the set 
time. There should be an appropriate 
amount of fuel in the burner head. 

Hot air gun running 
time at step 2 

30s 

0-360s 

Hot air gun operation time after flame 
detection (ignition phase 2). 

 

The automatic ignition is initialised either by the user or automatically by the 
accumulator upper temperature sensor. The storage auger automatically fills 
the funnel and the boiler is ventilated before ignition. When the funnel is full, 
the burne screw runs for the duration of the 

Burner screw filling time (long) 

-setting, feeding an appropriate amount of fuel to the burner head. NOTE! If 
the system is halted by an alarm while the burner screw is full of fuel, the user 
can select a short filling time during ignition. During the short filling, the screw 
will feed the burner head for the duration of the 

Burner screw filling time 

(short) 

-setting. 

The hot air gun and combustion air fans operate for the duration of the 

Ignition step 1

 -setting. If the flame detection detects a flame, the burner will 

activate the 

Ignition 2

 -phase. The optical flame detection sensor must detect 

a flame during the duration of the 

Flame delay

 -setting in order to activate the 

flame data. If the flame detection fails to detect a flame during the 

Ignition 

step 1

 -time setting, the fans and ignition stop and the 

Alarm! automatic 

ignition

 alarm is displayed. 

During the 

Ignition 2

 -phase, the burner runs at a power level configured in 

the 

Burner screw

 -setting for the duration of the 

Ignition step 2 

-setting. After 

this the burner automatically activates the effect mode. If the flame disappears 
during the 

Ignition 2

 -phase, the 

Alarm! Automatic ignition

 -alarm is 

displayed. 

Power settings for the burner screw and the combustion air fans during the 
ignition phases are set in the 

BURNER SCREW/PRIMARY 

FAN/SECONDARY FAN

 -setting pages. 

The hot air gun can be activated by pressing the IGNITION UP->EFFECT -
button once the burner switches from 

Upkeep

 to 

Effect 

mode. 

 

 

 

 

Содержание Arimatic 151












































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды