APRILIA DORSODURO 2007 Скачать руководство пользователя страница 76

Страница: 76 / 302

CAUTION: THE CIRCUIT SHOULD NOT BE ENERGISED, OTHERWISE THE TEST IS IRRELE-

VANT.

GROUND CONNECTION check

Check goal:

this control is to check if a cable or a circuit is in contact with the vehicle ground (-)

connection.

Tester: set the tester on the "continuity" symbol and place one tester probe on the vehicle ground

connection (or on the battery - terminal) and the other probe on the cable being inspected: the tester

sends out a sound signal only if there is continuity. The tester can also be set to the Ohm symbol to

check that the circuit resistance is null or a few tenths of an Ohm.

CAUTION! IF THERE IS A GROUND CONNECTION COMING FROM THE CONTROL UNIT, MAKE

SURE THAT DURING THE TEST THE CONTROL UNIT IS EARTH CONNECTED TO THE CIRCUIT.

VOLTAGE check

Check goal:

this control is to check if a cable is energised, i.e. if it receives power supply from the

battery or the control unit.

Tester:

set the tester on the direct current symbol and place the tester red probe on the cable being

inspected and the black probe on the vehicle ground connection (or on the battery - terminal).

CAUTION

IN CASE OF TEMPORAL MALFUNCTIONING, CARRY OUT ALL DUE CHECKS LOOKING FOR
FAILURES BY MOVING SLIGHTLY THE CABLE HARNESS BEING INSPECTED.

Dashboard

In case the EFI warning light turns on and the words SERVICE or URGENT SERVICE are shown on

the display, due to an error detected in the injection ECU, the malfunction indication will be deactivated

only after the vehicle has been used for a pre-set number of minutes of operation. However, even though

the malfunction is no longer present and the control unit considers the error no longer current but mem-

orised (MEM error indication on Axone), the instrument panel may keep showing there is an error

present.

Diagnosis

An access code is required to enter this menu which controls the diagnosis function:

•

ENTER SERVICE CODE

This is a 5-digit code, fixed for each vehicle. For these vehicles, the code is:

98789

If the code is incorrect, the following message is displayed:

•

INCORRECT CODE

and the instrument panel goes back to the main menu. Otherwise, the following menu is displayed:

•

EXIT

Electrical system

DORSODURO

ELE SYS - 76

Содержание DORSODURO 2007















































































































































































































































































































Результаты поиска

Содержание DORSODURO 2007

Отзывы:

Похожие инструкции для DORSODURO 2007

Бренды по названию

Популярные бренды

APRILIA DORSODURO 2007, Руководство по обслуживанию станции

Результаты поиска

Содержание DORSODURO 2007

Отзывы:

Похожие инструкции для DORSODURO 2007

Бренды по названию

Популярные бренды