APRILIA DORSODURO 2007 Скачать руководство пользователя страница 132

Страница: 132 / 302

Specification

Desc./Quantity

GREY BODY: Indicator reset

PIN 16

GREY BODY: Oil sensor input

PIN 17

GREY BODY: 750/1200 Selection

PIN 18

GREY BODY: *

PIN 19

GREY BODY: K Line

PIN 20

BLACK BODY: + Battery

PIN 21

BLACK BODY: Front left turn indicator activation

PIN 22

BLACK BODY: Front right turn indicator activation

PIN 23

BLACK BODY: Aerial 2

PIN 24

BLACK BODY: *

PIN 25

BLACK BODY: CAN H

PIN 26

BLACK BODY: CAN L

PIN 27

BLACK BODY: ABS warning light input

PIN 28

BLACK BODY: *

PIN 29

BLACK BODY: Ground for sensors

PIN 30

BLACK BODY: + Battery

PIN 31

BLACK BODY: Rear left turn indicator activation

PIN 32

BLACK BODY: Rear right turn indicator activation

PIN 33

BLACK BODY: Aerial 1

PIN 34

BLACK BODY: Light relay activation

PIN 35

BLACK BODY: *

PIN 36

BLACK BODY: *

PIN 37

BLACK BODY: General ground

PIN 38

BLACK BODY: General ground

PIN 39

BLACK BODY: General ground

PIN 40

Can line

CAN line

Function

It allows communication between the Marelli injection control unit, the throttle control unit and the in-

strument panel.

Level in wiring diagram:

CAN line

Pin-out:

see wiring diagram

AXONE: ELECTRICAL ERRORS

U1602 CAN line without signals

- Bus Off.

Error cause

•

No communication on CAN line (PIN 20 and/or PIN 51 VEHICLE): problem on the whole

network (for example, battery cut-off or short circuited or shorted to ground).

Troubleshooting

•

Check the Marelli control unit VEHICLE connector: if not OK, restore; if OK, check the earth

insulation of the two CAN lines from PIN 20 and PIN 51 of the VEHICLE connector: If not

OK, restore the cable harness; if OK, check continuity of the two CAN lines from the Marelli

control unit VEHICLE connector to the filter casing large connector and to the instrument

panel connector: if not OK, restore the cable harness; if OK, check that the two lines are not

shorted to positive testing each of the 3 connectors (Marelli control unit connector, filter

casing large connector and instrument panel connector) with 1 connector disconnected at

a time and by setting the key to ON: If not OK, restore; if OK, replace the Marelli control unit.

Mute Node CAN Line, U1601

- Mute Node

Electrical system

DORSODURO

ELE SYS - 132

Содержание DORSODURO 2007















































































































































































































































































































Результаты поиска

Содержание DORSODURO 2007

Отзывы:

Похожие инструкции для DORSODURO 2007

Бренды по названию

Популярные бренды

APRILIA DORSODURO 2007, Руководство по обслуживанию станции

Результаты поиска

Содержание DORSODURO 2007

Отзывы:

Похожие инструкции для DORSODURO 2007

Бренды по названию

Популярные бренды