APRILIA DORSODURO 2007 Скачать руководство пользователя страница 49 | Manualshive

Страница: 49 / 302

background image

Engine

The engine does not start

THE ENGINE DOES NOT START

CAUTION

AXONE SHOULD BE WORKING PROPERLY AND UPGRADED TO THE 5.1.5 VERSION MINIMUM.

CAUTION

BEFORE ANY TROUBLESHOOTING, MAKE SURE THAT:
1) BATTERY VOLTAGE IS ABOVE 12V;
2) THE MAIN 30A FUSE IS NOT DAMAGED AND IS ADEQUATELY FITTED;
3) AUXILIARY FUSES ARE NOT DAMAGED AND ARE ADEQUATELY FITTED.

NOTE

THE RELAY NUMBER SPECIFIED REFERS TO THE WIRING DIAGRAM. THE POSITION OF THE
RELAY ON THE VEHICLE IS INDICATED IN THE "ELECTRICAL SYSTEM/COMPONENT LAYOUT/
RELAY LAYOUT" CHAPTER.

•

1 - WITH THE KEY TURNED TO "ON", THE INSTRUMENT PANEL LIGHTS UP BUT NO

FAILURE INDICATION IS SHOWN. IS THE FUEL PUMP ACTIVATED?

YES, go to 27; NO, go to 2

•

2 - DOES AXONE COMMUNICATE WITH THE CONTROL UNIT?

YES, go to 3; NO, go to 4

•

3 - ACTIVATE ONE INJECTOR BY MEANS OF AXONE ("DEVICES ACTIVATION"

SCREEN PAGE, INJECTOR ICON): IS THE INJECTOR ACTIVATED?

YES, go to 17; NO, go to 12

•

4 -WITH THE KEY TURNED TO "OFF" CHECK IF THERE IS VOLTAGE ON THE ORANGE/

RED CABLE OF THE MAIN INJECTION RELAY (POLARISED) 41.

YES, go to 6; NO, go to 5

•

5 - INSPECT IF THERE IS AN INTERRUPTION IN THE ORANGE/RED CABLE FROM THE

MAIN INJECTOR RELAY (POLARISED) TO THE BATTERY POSITIVE.

•

6 - WITH THE KEY TURNED TO "ON" CHECK IF THERE IS VOLTAGE ON THE GREEN/

BLACK CABLE OF THE MAIN INJECTION RELAY (POLARISED) 41.

OK, go to 8; NOT OK, go to 7

•

7 - INSPECT THE GREEN/BLACK CABLE FROM THE MAIN INJECTION RELAY (PO-

LARISED) 41 TO THE KEY SWITCH - END

•

8 - IS THE BLUE CABLE GROUNDED?

YES, go to 10; NO, go to 9

•

9 - RESTORE THE CABLE HARNESS.

•

10 - CHECK IF THERE IS VOLTAGE ON THE RED/BLACK CABLE.

NOT OK, go to 11; OK, go to 12

DORSODURO

Troubleshooting

TROUBL - 49

«
...
47
48
49
50
51
...
»

Содержание DORSODURO 2007















































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DORSODURO 2007

Бренд: Caberg Страницы: 16

Soft Luggage Pannier Racks

Бренд: Honda Страницы: 10

Бренд: hepco & becker Страницы: 4

Fastrax 50144-00

Бренд: Dowco Страницы: 3

Stealth Air Cleaner Kit

Бренд: S&S Cycle Страницы: 4

Бренд: Ducati Страницы: 77

Бренд: R&G Страницы: 6

Бренд: hepco & becker Страницы: 7

Бренд: SHERCO Страницы: 102

Бренд: KTM Страницы: 36

Aquila GT250 R Ej

Бренд: HYOSUNG Страницы: 37

Бренд: DYNATEK Страницы: 11

Бренд: Yamaha Страницы: 5

Бренд: Yamaha Страницы: 22

Бренд: Yamaha Страницы: 34

Бренд: Yamaha Страницы: 34

Бренд: Yamaha Страницы: 39

Бренд: Yamaha Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды