APRILIA DORSODURO 2007 Скачать руководство пользователя страница 52

Страница: 52 / 302

•

44 - CHECK IF THERE IS VOLTAGE IN THE RED/BLACK CABLES ON THE CONTROL

RELAY (START-UP LOGIC) 40

YES, go to 50; NO, go to 51

•

45 - CHECK CONTINUITY AND GROUND INSULATION OF THE YELLOW/PINK CABLE

FROM THE RELAY TO THE ENGINE CONNECTOR (PIN 2)

OK, go to 47; NOT OK, go to 46

•

46- RESTORE THE CABLE HARNESS - END

•

47 - CHECK THE CONTROL UNIT CONNECTOR

OK, go to 49; NOT OK, go to 48

•

48 - RESTORE THE CABLE HARNESS - END

•

49 - REPLACE THE CONTROL UNIT - END

•

50 - PRESSING THE STARTER BUTTON, DISCONNECT THE CONNECTOR OF THE

WHITE/SKY BLUE AND WHITE/RED CABLES OF THE START-UP RELAY 36, AND

CHECK IF THERE IS VOLTAGE TO THE YELLOW/RED CABLE OF THE CONTROL RE-

LAY- START-UP LOGIC- 40

OK, go to 52; NOT OK, go to 53

•

51 - REPLACE THE RELAY - END

•

52 - PRESSING THE STARTER BUTTON, CHECK IF THERE IS VOLTAGE TO THE YEL-

LOW/RED CABLE OF THE START-UP RELAY

OK, go to 54; NOT OK, go to 55

•

53 - REPLACE THE RELAY - END

•

54 - CHECK IF THE BLUE CABLE OF THE START-UP RELAY 36 IS GROUNDED

OK, go to 56; NOT OK, go to 57

•

55 - RESTORE THE CABLE HARNESS -END

•

56 - WITH THE KEY TURNED TO "OFF" CHECK IF THERE IS VOLTAGE TO THE REAR

RED CABLE (WITH PROTECTION COVER) OF THE START-UP RELAY 36

OK, go to 58; NOT OK, go to 59

•

57 - RESTORE THE CABLE HARNESS -END

•

58 - PRESSING THE STARTER BUTTON, CHECK IF THERE IS VOLTAGE TO THE

FRONT RED CABLE OF THE START-UP RELAY 36

OK, go to 60; NOT OK, go to 61

•

59 - RESTORE THE CABLE HARNESS

•

60 - CHECK CONTINUITY OF THE RED CABLE BETWEEN THE START-UP RELAY 36

AND THE STARTER MOTOR

YES, go to 62; NO, go to 63

Troubleshooting

DORSODURO

TROUBL - 52

Содержание DORSODURO 2007















































































































































































































































































































Результаты поиска

Содержание DORSODURO 2007

Отзывы:

Похожие инструкции для DORSODURO 2007

Бренды по названию

Популярные бренды

APRILIA DORSODURO 2007, Руководство по обслуживанию станции

Результаты поиска

Содержание DORSODURO 2007

Отзывы:

Похожие инструкции для DORSODURO 2007

Бренды по названию

Популярные бренды