APRILIA DORSODURO 2007 Скачать руководство пользователя страница 23

Страница: 23 / 302

Crankcase category

Crankcase can be selected from two types (A or

B) according to the centre to centre distance be-

tween the primary reduction gears.

The category can be checked out on clutch-side

crankcase half, at the back.

NOTE

SHOULD THE CRANKCASE BE REPLACED, THIS IS SUP-
PLIED WITH THE PRIMARY REDUCTION GEAR ALREADY
COUPLED.

RANKCASE

SELECTION

TYPE

Specification

Desc./Quantity

Type A crankcase

Centre to centre distance: 110.50 - 110.54 mm (4.3504 -

4.3519 in)

Type B crankcase

Centre to centre distance: 110.46 - 110.50 mm (4.3488 -

4.3504 in)

Primary category

Pinion can be selected from two types (A or B) ac-

cording to the centre to centre distance between

the primary reduction gears.

The category can be checked out on the pinion it-

self.

Crankshaft category

Shaft can be selected from two types (1 or 2) ac-

cording to the crank pin diameter.

Shaft can be selected from seven types (E1,

E2, ...) according to connecting rod weight.

RANKSHAFT

SELECTION

TYPE

Specification

Desc./Quantity

Crankshaft type 1

Crank pin diameter: 41.994 - 42.000 mm (1.65330 - 1.65354

in)

Crankshaft type 2

Crank pin diameter: 41.988 - 41.994 mm (1.65307 - 1.65330

in)

Bushing selection

The connecting rod has only one size category. Therefore, bushings are chosen only based on crank-

shaft type.

DORSODURO

Characteristics

CHAR - 23

Содержание DORSODURO 2007















































































































































































































































































































Результаты поиска

Содержание DORSODURO 2007

Отзывы:

Похожие инструкции для DORSODURO 2007

Бренды по названию

Популярные бренды

APRILIA DORSODURO 2007, Руководство по обслуживанию станции

Результаты поиска

Содержание DORSODURO 2007

Отзывы:

Похожие инструкции для DORSODURO 2007

Бренды по названию

Популярные бренды