APRILIA DORSODURO 2007 Скачать руководство пользователя страница 90

Страница: 90 / 302

•

if the circuit is open, short circuit to negative: check the throttle grip sensor connector and

the Marelli control unit connector. If not OK, restore. If OK, check circuit continuity between

the two cable terminals. If not OK, restore; if OK, check the cable earth insulation (from the

throttle grip sensor connector or the control unit connector): if the cable is not earth insulated,

restore the wiring. If it is earth insulated, and with the switch key set to ON, check that there

is power supply for the potentiometer PIN D and that PIN F is connected to earth. If both are

correct, replace the throttle grip sensor; if not, check the continuity of the cable that is not

functioning properly: if there is continuity, replace the control unit; if not, restore the wiring.

Right side Throttle Grip Position sensor - track C P0152-

short circuit to positive / open circuit, short

circuit to negative.

Error cause

•

If shorted to positive: excessive voltage has been detected at PIN 30 of the ENGINE con-

nector. If the circuit is open, shorted to negative: voltage equal to zero has been detected

at PIN 30 of the ENGINE connector.

Troubleshooting

•

if shorted to positive: check the value shown by the parameter of the right Throttle Grip

position Sensor - track C: disconnect the right side connector and see the value displayed

by the Axone: if the voltage does not vary, there is a short circuit in the cable wiring; replace

the throttle grip sensor if the voltage drops to zero.

•

if the circuit is open, short circuit to negative: check the throttle grip sensor connector and

the Marelli control unit connector. If not OK, restore. If OK, check circuit continuity between

the two cable terminals. If not OK, restore; if OK, check the cable earth insulation (from the

throttle grip sensor connector or the control unit connector): if the cable is not earth insulated,

restore the wiring. If it is earth insulated, and with the key set to ON, check that there is

power supply for the potentiometer PIN A and that PIN C is connected to earth. If both are

correct, replace the throttle grip sensor; if not, check the continuity of the cable that is not

functioning properly: if there is continuity, replace the control unit; if not, restore the wiring

Right side Throttle Grip Position sensor - track D P0153

- short circuit to positive / open circuit, short

circuit to negative.

Error cause

•

If shorted to positive: excessive voltage has been detected at PIN 44 of the ENGINE con-

nector. If the circuit is open, shorted to negative: voltage equal to zero has been detected

at PIN 44 of the ENGINE connector.

Troubleshooting

•

if shorted to positive: check the value shown by the parameter of the right Throttle Grip

Position Sensor - track D: disconnect the right side connector and see the value displayed

Electrical system

DORSODURO

ELE SYS - 90

Содержание DORSODURO 2007















































































































































































































































































































Результаты поиска

Содержание DORSODURO 2007

Отзывы:

Похожие инструкции для DORSODURO 2007

Бренды по названию

Популярные бренды

APRILIA DORSODURO 2007, Руководство по обслуживанию станции

Результаты поиска

Содержание DORSODURO 2007

Отзывы:

Похожие инструкции для DORSODURO 2007

Бренды по названию

Популярные бренды