APRILIA DORSODURO 2007 Скачать руководство пользователя страница 57

Страница: 57 / 302

•

Location on the vehicle: under the saddle.

AUXILIARY INJECTION RELAY

•

Location on the wiring diagram: 40

•

Location on the vehicle: under the fuel tank, right side, third relay starting from the front.

FAN CONTROL RELAY

•

Location on the wiring diagram: 42

•

Location on the vehicle: under the fuel tank, left side, first relay starting from the front.

HIGH-BEAM LIGHTS RELAY

•

Location on the wiring diagram: 64

•

Location on the vehicle: under the fuel tank, left side, third relay starting from the front.

RECOVERY LOGIC RELAY (URGENT SERVICE)

•

Location on the wiring diagram: 65

•

Location on the vehicle: under the fuel tank, right side, fourth relay starting from the front.

Electrical system installation

INTRODUCTION

Scope and applicability

The position of the cable harnesses, how they are fixed to the motorcycle and potential problems are

defined on the following sections in order to reach the objectives of vehicle reliability.

Materials used and corresponding quantities

The electrical system consists of the following cable harnesses and parts:

•

1 Main Cable Harness

•

1 Filter Casing Cable Harness

•

1 Rear light Cable harness

•

1 Relay-Starter Motor Cable

•

1 Battery - Engine Ground Cable

•

2 Caps for Magura Switches

•

1 Injection Main Relay

•

6 Relays 12 V / 30 A

•

1 Start-up Relay

•

Medium black clamps 178 x 4 (7.01 x 0.16 in)

•

Small black clamps 98 x 2.5 (3.86 x 0.01 in)

•

1 10-cm (3.94 in) spiral for start-up cable

•

1 Pick-Up divider cable harness (if fitted)

Vehicle sections

The wiring distribution is subdivided in three essential sections, as indicated in the figure.

DORSODURO

Electrical system

ELE SYS - 57

Содержание DORSODURO 2007















































































































































































































































































































Результаты поиска

Содержание DORSODURO 2007

Отзывы:

Похожие инструкции для DORSODURO 2007

Бренды по названию

Популярные бренды

APRILIA DORSODURO 2007, Руководство по обслуживанию станции

Результаты поиска

Содержание DORSODURO 2007

Отзывы:

Похожие инструкции для DORSODURO 2007

Бренды по названию

Популярные бренды