APRILIA DORSODURO 2007 Скачать руководство пользователя страница 121 | Manualshive

Страница: 121 / 302

background image

BEFORE CARRYING OUT ANY TROUBLESHOOTING, CAREFULLY READ THE GENERAL CON-
CEPTS OF ELECTRICAL TROUBLESHOOTING FOUND AT THE BEGINNING OF THE CHECKS
AND CONTROLS SECTION IN THE ELECTRICAL SYSTEM CHAPTER.

AXONE: STATUSES

Gear in neutral

Example value:

yes/no

AXONE: NOTES

•

Indication on the instrument panel always gear engaged: check the correct position of the

cable terminals on the connector and the correct connection of the cables on the terminals.

If they are not correct, restore the cable harness; if correct, disconnect the connector and,

with gear in neutral, check continuity to terminal ground connection, sensor side: if there is

no continuity, replace the sensor (after checking cable continuity on the sensor side and the

correct mechanical position). If there is, check the correct position of the terminal on the

control unit connector and the correct connection of the cables on the terminals. If they are

not correct, restore the cable harness; if OK, check the cable continuity between the sensor

connector and ENGINE connector PIN 16: if there is no continuity, restore the cable harness.

If there is, replace the instrument panel if the vehicle performance is correct (the engine

starts with gear in neutral but the neutral warning light is off) or replace the control unit if the

vehicle performance is not correct (the engine does not start with gear in neutral).

•

Indication on the instrument panel always gear in neutral: disconnect the terminals from the

sensor and check if there is continuity with ground connection at PIN toward the sensor, with

gear engaged: if there is continuity, replace the sensor. If it is insulated from the ground

connection, it means that the green/black cable from sensor PIN 1 to ENGINE connector

PIN 16 is shorted to ground: restore the cable harness

Clutch lever sensor

CLUTCH LEVER SENSOR

Function

It tells the clutch lever position to the control unit.

Operation / Operating principle

If there is gear engaged but the clutch is pulled, i.e. circuit closed to ground, vehicle start-up is not

enabled.

Level in wiring diagram:

Start-up enabling switches.

Location:

•

on the vehicle: under clutch lever

•

connector: on the sensor

Electrical characteristics:

DORSODURO

Electrical system

ELE SYS - 121

«
...
119
120
121
122
123
...
»

Содержание DORSODURO 2007















































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DORSODURO 2007

Бренд: Cake Страницы: 13

EC-SIX DAYS - PART LIST 2011

Бренд: GAS GAS Страницы: 6

6513515 00 22-00-40

Бренд: hepco & becker Страницы: 7

Бренд: PUIG Страницы: 2

Dirt rocket XM500

Бренд: X-TREME scooter Страницы: 14

Бренд: Yamaha Страницы: 90

Бренд: Yamaha Страницы: 435

Бренд: Shad Страницы: 12

Бренд: Shad Страницы: 2

Бренд: Shad Страницы: 2

TOPMASTER V0NR55ST

Бренд: Shad Страницы: 2

TOPMASTER Y0TM52ST

Бренд: Shad Страницы: 3

Бренд: Shad Страницы: 4

Бренд: KOOFU Страницы: 24

XSM POWER UP 2007

Бренд: Malaguti Страницы: 53

Бренд: Piaa Страницы: 17

Бренд: APRILIA Страницы: 170

FBG-P-RAN-09-XP

Бренд: SuperATV Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды