APRILIA DORSODURO 2007 Скачать руководство пользователя страница 186

Страница: 186 / 302

Top ring (1st slot): 0.030 - 0.065 mm (0.0012 -

0.0026 in)

Intermediate ring (2nd slot): 0.020 - 0.055 mm

(0.0008 - 0.0022 in)

Oil scraper ring (3rd slot): 0.010 - 0.045 mm

(0.0004 - 0.0018 in)

•

Fit the piston ring to the cylinder.

•

Level the installed piston ring with the

piston crown.

•

Measure piston ring port and replace it

if not complying with specifications.

CAUTION

IT IS NOT POSSIBLE TO MEASURE THE GAP OF THE OIL
SCRAPER RING END: IF CLEARANCE IS EXCESSIVE, RE-
PLACE THE THREE PISTON RINGS.

Piston ring end gap:

Top ring: 0.25 - 0.40 mm (0.0079 - 0.0157 in)

Intermediate ring: 0.35 - 0.55 mm (0.0138 -

0.0216 in)

Oil scraper ring: 0.20 - 0.70 mm (0.0079 - 0.0276

in)

PIN

•

Clean off combustion residues from the piston crown and from the area above the top ring.

•

Check for cracks on the piston and for compression on the piston sliding surface (seizing);

Replace the piston if required.

CAUTION

SMALL STRIATIONS ON THE PISTON LINER ARE ADMISSIBLE.

•

Measure the pin outside diameter (a)

and if not complying with specifica-

tions, replace the pin.

Pin outside diameter: 22.00 - 21.97 mm (0.8661

- 0.8650 in) Limit: 21.96 mm (0.8646 in)

Engine

DORSODURO

ENG - 186

Содержание DORSODURO 2007















































































































































































































































































































Результаты поиска

Содержание DORSODURO 2007

Отзывы:

Похожие инструкции для DORSODURO 2007

Бренды по названию

Популярные бренды

APRILIA DORSODURO 2007, Руководство по обслуживанию станции

Результаты поиска

Содержание DORSODURO 2007

Отзывы:

Похожие инструкции для DORSODURO 2007

Бренды по названию

Популярные бренды