APRILIA DORSODURO 2007 Скачать руководство пользователя страница 9

Страница: 9 / 302

When repairing, dismantling and reassembling the vehicle follow the recommendations reported below

carefully.

BEFORE DISASSEMBLING COMPONENTS

•

Before dismantling components, remove dirt, mud, dust and foreign bodies from the vehicle.

Use the special tools designed for this bike, as required.

COMPONENTS REMOVAL

•

Do not loosen and/or tighten screws and nuts using pliers or other tools other than the

especially designed wrench.

•

Mark positions on all connection joints (pipes, cables, etc.) before separating them, and

identify them with distinctive symbols.

•

Each component needs to be clearly marked in order to be identified during assembly.

•

Clean and wash the removed components carefully using a low-flammability detergent.

•

Keep coupled parts together since they have "adjusted" to each other due to normal wear

and tear.

•

Some components must be used together or replaced altogether.

•

Keep away from heat sources.

REASSEMBLING COMPONENTS

CAUTION

BEARINGS MUST BE ABLE TO ROTATE FREELY, WITHOUT JAMMING AND/OR NOISE, OTH-
ERWISE THEY NEED REPLACING.

•

Only use ORIGINAL APRILIA SPARE PARTS.

•

Comply with lubricant and consumables use guidelines.

•

Lubricate parts (whenever possible) before reassembling them.

•

When tightening nuts and screws, start from the ones with the largest section or from the

internal ones, moving diagonally. Tighten nuts and screws in successive steps before ap-

plying the tightening torque.

•

Always replace self-locking nuts, washers, sealing rings, circlips, O-rings (OR), split pins

and screws with new ones if their tread is damaged.

•

When assembling the bearings, make sure to lubricate them well.

•

Check that each component is assembled correctly.

•

After a repair or routine maintenance procedure, carry out pre-ride checks and test the ve-

hicle on private grounds or in an area with low traffic density.

•

Clean all coupling surfaces, oil guard rims and gaskets before refitting them. Smear a light

layer of lithium-based grease on the oil guard rims. Reassemble oil guards and bearings

with the brand or lot number facing outward (visible side).

ELECTRIC CONNECTORS

Electric connectors must be disconnected as described below as non-compliance with the procedure

so described causes irreparable damage to both the connector and the cable harness:

DORSODURO

Characteristics

CHAR - 9

Содержание DORSODURO 2007















































































































































































































































































































Результаты поиска

Содержание DORSODURO 2007

Отзывы:

Похожие инструкции для DORSODURO 2007

Бренды по названию

Популярные бренды

APRILIA DORSODURO 2007, Руководство по обслуживанию станции

Результаты поиска

Содержание DORSODURO 2007

Отзывы:

Похожие инструкции для DORSODURO 2007

Бренды по названию

Популярные бренды