Antec Leyden DECADE II Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 42

background image

26 Installation guide

10. Configuration of dip switches

In order for the embedded software of the DECADE II to recognize both
boards properly the board address of the sensor boards should be set by
means of the dip switches. The dip switches are located between the BNC
connector and sub-D I/O connector at the edge of the board. The dipswitches
are protected by means of a brown transparent foil. Remove this adhesive foil
to free switches for programming. Program the dips switches as depicted in
figure 19 and 20 for sensor board 1 and 2 respectively.

Figure 19 Dip switch settings for sensor board 1: 1-on, 2-on, 3-on and 4-on.

Figure 20 Dip switch settings for sensor board 2: 1-on, 2-off, 3-on and 4-on.

Please place the transparent adhesive foil back after programming for
protection.

«
...
26
27
28
29
30
...
»

Содержание DECADE II











































Отзывы:

Нет отзывов

Похожие инструкции для DECADE II

Бренд: Keithley Страницы: 36

Бренд: Rain-Flo Irrigation Страницы: 16

BTL PA0400 Series

Бренд: Balluff Страницы: 22

Micropulse BTL5 Series

Бренд: Balluff Страницы: 12

BNI IOW-560-W01-K022

Бренд: Balluff Страницы: 32

Бренд: Baltic Страницы: 68

Бренд: Baltic Страницы: 68

Max Charge MC-612

Бренд: Balmar Страницы: 12

BTL PA0400 Series

Бренд: Balluff Страницы: 204

Бренд: dbx Страницы: 12

Бренд: dbx Страницы: 13

Бренд: dbx Страницы: 72

Бренд: dbx Страницы: 11

Бренд: dbx Страницы: 16

Бренд: Eagle Eye Страницы: 21

Бренд: Labomed Страницы: 67

Бренд: Xo Страницы: 59

Бренд: Kamikaze Страницы: 112

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды