Antec Leyden DECADE II Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 42

background image

16 Installation guide

Both the internal cell cable and the I

2

C/power cable of sensor board 1 should

be labelled for identification using the vinyl label marked "sensor 1" provided
in the kit. The labels can be found in the white envelope (p/n 171.0208).
Label the cables as depicted in figure 5. Place label at the end of the cable
next to the connectors which are mounted on sensor board 1.

Figure 5

Labelling of cables sensor board 1.

Label the internal cell cable of sensor board 2 with a vinyl label marked
"Sensor 2". The internal cell cable for sensor board 2 is not connected to any
board and is fixed in the black cable clamp mounted to the top cover inside
the housing.

«
...
16
17
18
19
20
...
»

Содержание DECADE II











































Отзывы:

Нет отзывов

Похожие инструкции для DECADE II

D-IMager EKL3104

Бренд: Panasonic Страницы: 13

Бренд: Labokey Страницы: 5

Бренд: E-Z Trail Страницы: 8

Бренд: B&K Страницы: 10

Бренд: Above All Страницы: 4

Бренд: Federal Signal Corporation Страницы: 2

Бренд: Harman Kardon Страницы: 7

Бренд: ECE Страницы: 2

Бренд: Ecco Страницы: 5

Evolution Series

Бренд: Bakare Страницы: 38

Бренд: Nitecore Страницы: 4

Lab companion SI-300

Бренд: Jeio tech Страницы: 69

IP Video Test Option HST-3000

Бренд: JDS Uniphase Страницы: 4

Бренд: Jct Страницы: 16

Бренд: L-Acoustics Страницы: 5

Бренд: York Страницы: 16

i.Profiler plus

Бренд: Zeiss Страницы: 66

Бренд: GE Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды