Antec Leyden DECADE II Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 42

background image

28 Installation guide

12. Installation of sensor boards

•

Mount sensor board 1 to rear panel.

•

Connect the corresponding internal cell cable and power cable on
sensor board 1.

•

Mount sensor board 2 to rear panel.

•

Connect the corresponding internal cell cable and power cable on
sensor board 2. To install the internal cell cable of board 2 use the D-
connector mounting set provided. Only the hex screws (see figure
22) should be used of the D-connector mounting set. Other parts can
be disposed. Mount the connector in the same way as in the case of
sensor board 1 using the hex screws and two plastic rings.

Figure 17 D-connector mounting set.

Figure 22 D-connector mounting set

•

Fix rear panel on the DECADE II (see figure 2).

13. Installation of cell and column clamps

•

Fix the black cell clamp for the second flow cell inside the oven
compartment in the middle between the fans using one of the
three available M4 screw holes.

•

If necessary fix the two grey 12 mm column clamps using the
available M3 screw holes located on the left and right side in the
oven compartment. Remove the plastic protective covers from
the M3 screw holes prior to installation.

«
...
28
29
30
31
32
...
»

Содержание DECADE II











































Отзывы:

Нет отзывов

Похожие инструкции для DECADE II

Бренд: Jackco Страницы: 6

Бренд: dbx Страницы: 2

Бренд: Nautilus Страницы: 17

Бренд: National Instruments Страницы: 6

Бренд: WalkMed Страницы: 2

Бренд: Walinga Страницы: 20

Бренд: Panasonic Страницы: 23

Бренд: Onwa Страницы: 35

Бренд: KAM Страницы: 5

CB Ohio Special 100 HP

Бренд: CleaverBrooks Страницы: 200

Бренд: Nahita Страницы: 31

Бренд: Lettuce Grow Страницы: 8

Бренд: Waldman Страницы: 60

Бренд: Struers Страницы: 95

Chopper 6500 SK30

Бренд: Jäger Страницы: 40

Бренд: Gaspardo Страницы: 176

Бренд: laerdal Страницы: 170

Tough Dual-Probe Bale Spear

Бренд: Bush Hog Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды