Antec Leyden DECADE II Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 42

background image

2

Safety practices

The following safety practices are intended to insure safe operation of the
equipment.

Electrical hazards

The removal of protective panels on the instrument can result in exposure to
potentially dangerous voltages. Therefore, disconnect the instrument from all
power sources before disassembly. Untrained personnel should not open the
instrument.

Replace blown fuses with fuses of proper type and rating as stipulated on the
rear panel and specified in the installation section of this manual. The fuse
holder is integrated in the mains connector. Ensure that the instrument is
never put in operation with fuses of a different type. This could cause fire.

USE ONLY WITH 250 V FUSES

EMPLOYER UNIQUEMENT

AVEC DES FUSIBLES DE 250V

Connect the detector to a grounded AC power source, line voltage 100 – 240
VAC. The instrument should be connected to a protective earth via a ground
socket. The power source should exhibit minimal power transients and
fluctuations. Replace faulty or frayed power cords.

«
...
2
3
4
5
6
...
»

Содержание DECADE II











































Отзывы:

Нет отзывов

Похожие инструкции для DECADE II

Бренд: Baker Страницы: 82

Бренд: Panlux Страницы: 2

Бренд: Farmet Страницы: 102

Бренд: Hacker Страницы: 2

Бренд: J.P. SELECTA Страницы: 8

Бренд: Haemonetics Страницы: 134

Бренд: Hadeco Страницы: 72

Бренд: HALDER Страницы: 2

Бренд: Hakko Electronics Страницы: 16

Бренд: ICP DAS USA Страницы: 45

Бренд: Nellcor Страницы: 161

OXIMAX N-600X Series

Бренд: Nellcor Страницы: 210

Бренд: Oase Страницы: 120

Бренд: OAKWORKS Страницы: 24

Бренд: Saadat Страницы: 61

Бренд: Saadat Страницы: 22

Бренд: TDR Страницы: 8

QUICK-ALIGN Vari-Flex

Бренд: Össur Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды