Antec Leyden DECADE II Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 42

background image

CHAPTER 2 DECADE II DCC upgrade kit install guide, edition 5

11

Installation procedure

The installation procedure consists of the following steps:

1. Upload of FW version 3.20 >

2. Removing rear panel

3. Installation of internal cell cable

(for s/n < 17100072 only)

4. Labelling cables for identification

5. Removing sensor board

6. Replacement of boot EPROMS

(for s/n < 17100092 only)

7. Reconfiguration

of heater connector 7

(for s/n < 17100092 only)

8. Installation of temperature control board

(for s/n < 17100092 only)

9. Installation of power cable for 2

nd

sensor board

10. Configuration of dip switches

11. Placement of I/O label on rear panel

12. Installation of sensor boards

13. Installation of cell and column clamps

14. Placement of cell identification labels

15. Upload of firmware version 3.xx

16. Check & calibration

For upgrade kit with p/n 171.0216 the installation steps 3, 6, 7 and 8 can

be skipped.

For upgrade kit with p/n 171.0218 the installation step 3 can be

skipped.

For upgrade kit with p/n 171.0220 ALL installation steps should be

executed.

«
...
11
12
13
14
15
...
»

Содержание DECADE II











































Отзывы:

Нет отзывов

Похожие инструкции для DECADE II

SACE Tmax XT Series

Бренд: ABB Страницы: 11

Бренд: ParaBody Страницы: 4

Бренд: DARAY Страницы: 28

Бренд: MacDon Страницы: 88

Бренд: Jiffy Страницы: 15

Бренд: Obdstar Страницы: 10

Бренд: HALDER Страницы: 2

Бренд: Hakko Electronics Страницы: 16

Бренд: Taurus Страницы: 24

Бренд: NatureZap Страницы: 2

ProFire Lightbridge

Бренд: M-Audio Страницы: 8

Бренд: M-Audio Страницы: 36

Бренд: Waters Страницы: 4

Бренд: Waterpik Страницы: 2

Бренд: Yamaha Страницы: 48

Бренд: YASKAWA Страницы: 81

Бренд: YASKAWA Страницы: 52

bionic power knee

Бренд: Össur Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды