andrews LWH42 Скачать руководство пользователя | Manualshive

Страница: 35 / 64

background image

31

• Do not extend the flue pipe longer than the maximum limits as stated in the installation manual.

The flue lengths longer than the stated maximum are dangerous and may cause a fire or explosion.

• Avoid installing the flue pipe in an enclosure if possible.
• Do not install a damper on the intake or exhaust pipe.
• Do not install the flue terminal indoors.
• Use 100 mm diameter type the flue pipe from the water heater all the way to the flue terminal.
• Make sure that the flue pipe is sealed gas tight and is securely connected so that it cannot be

easily dislodged.

• Make the vertical section of the flue pipe as short as possible (1 m or less is suggested)
• Support the flue pipe at appropriate interval with hangers.

Installer must prepare the hunger for 100 mm diameter type, in case of necessity.
Refer to the flue pipe manufacture’s installation instructions for the proper interval.

• Steam or condensed water may drip out of the flue terminal. Dispose of this condensed water

according to local codes and in order to prevent injury or property damage.

Protection from condensed water accumulation

• Slope the intake and exhaust pipes at a 1/50 grade down towards the termination.
• Avoid sags or slack in the flue pipe.
• If the flue terminal will be installed higher than the water heater, make the vertical section directly

above the water heater as short as possible, and slope down to the terminal. Do not have another
vertical section after the horizontal section begins.

Intake pipe connection

Intake pipe connection

Exhaust pipe connection

Exhaust pipe
connection

Water heater

Flue pipe installation precautions

Flue Terminal

15-1-5. Installation Overview

(L)WH42̲56(25̲32)̲E

05.10.4, 1:35 PM

31

«
...
33
34
35
36
37
...
»

Содержание LWH42

































































Отзывы:

Нет отзывов

Похожие инструкции для LWH42

Бренд: YAMADA Страницы: 84

Бренд: Sioux Tools Страницы: 54

Бренд: Vectra Fitness Страницы: 28

Бренд: Ispring Страницы: 6

Бренд: Patron Страницы: 8

Beta b BT4b Series

Бренд: ProMinent Страницы: 108

Бренд: A.O. Smith Страницы: 16

Бренд: Orbegozo Страницы: 25

Бренд: Connect Страницы: 24

Бренд: Daikin Страницы: 44

Бренд: T.I.P. Страницы: 136

Бренд: NARVI Страницы: 40

Бренд: umbra pompe Страницы: 46

Бренд: Goldair Страницы: 12

Бренд: VADA Страницы: 6

ESSENSSE NEO VCES2-B-AC Series

Бренд: 2VV Страницы: 20

Бренд: MPM Страницы: 24

Бренд: Avalon Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды