andrews LWH42 Скачать руководство пользователя | Manualshive

Страница: 18 / 64

background image

14

Main unit

Straight pipe

• Do not store hazardous or flammable sub-

stances near the flue terminal.

• Slope the intake and exhaust pipes at a 1/50

grade down towards the termination.

• Connect the flue pipe firmly so that it will prevent

exhaust gases from leaking.

• Steam or condensed water may drip out of the

flue terminal. Dispose of this condensed water
according to local codes and in order to prevent
injury or property damage.

• Fit condensate trap and siphon to flues over 2m high.
• If this product will be installed in an area where

snow is known to accumulate,protect the flue ter-
mination from blockage by snow drifts or dam-
age from snow falling off of roofs.

• Support the flue pipe with hangers at intervals.
• Install the flue terminal so that it is easily acces-

sible for maintenance both from the indoors and
the outdoors.

• If the flue terminal will be installed higher than

the water heater,make the vertical section di-
rectly above the water heater as short as
possible,and slope down to the terminal. Do not
have another vertical section after the horizontal
section begins.

• Make the vertical pipe as short as possible.

Flue Precautions

• Use 100mm diameter flue pipe.
• Maximum flue length
4 elbow (90 degree) +
7m (flue pipe) + Flue Terminal
1 elbow (90 degree) +
12m (flue pipe) + Flue Terminal

• Minimum flue length
1 elbow (90 degree) + Flue Terminal
• Exceeding the maximum flue length is danger-

ous and may result in bad combustion.

• Maximum 90 degree bends not to exceed 4.
• Maximum length must be reduced by 2000mm

for each 90

°

bend used.

• Maximum length must be reduced by 1000mm

for each 45

°

bend used.

• If possible, don’t install the flue pipe through

any enclosed areas. If necessary, consult
ANDREWS WATER HEATER for clearances.

• Install the flue terminal so that all exhaust is

directed to and all intake air is taken from
outdoors.

Elbow

Elbow

Flue Terminal

sloping down

Intake pipe

Exhaust
pipe

Flue system installation example

M&G VERTICAL FLUE TERMINAL

• Use only the following models of the flue terminals with this unit.

Seal any connections that
are not gas tight using a
high temperature silicone
sealant.

Special
adapter

Main unit

Straight pipe

Flue Terminal

Intake pipe

Exhaust pipe

Flue system installation example

Seal any connections that
are not gas tight using a
high temperature silicone
sealant.

Special adapter

hangers

hangers

• The M&G Vertical Flue Terminal can be cut to suit the roof.

Special adapter

Roof thickness

50 mm to 500 mm

(L)WH42̲56(09̲15)̲E

05.9.28, 3:33 PM

Page 14

Adobe PageMaker 6.5J/PPC

«
...
16
17
18
19
20
...
»

Содержание LWH42

































































Отзывы:

Нет отзывов

Похожие инструкции для LWH42

Бренд: Watson Marlow Pumps Страницы: 131

Бренд: Eaton Страницы: 57

Бренд: A.O. Smith Страницы: 2

Бренд: A.O. Smith Страницы: 2

Бренд: Waterstone Страницы: 6

Бренд: DAYLIFF Страницы: 12

Бренд: Larius Страницы: 56

Бренд: La Hacienda Страницы: 5

Бренд: Zazen Страницы: 8

Craftsman 390.269451

Бренд: Sears Страницы: 8

Бренд: B+BTec Страницы: 20

Бренд: Hellenbrand Страницы: 8

Бренд: Northern Radiator Страницы: 2

Бренд: Aurora Scientific Страницы: 14

MENAI D E - MOUNTING

Бренд: RADSON Страницы: 4

Бренд: ARESA Страницы: 13

Бренд: SereneLife Страницы: 5

Бренд: P1 Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды