andrews LWH42 Скачать руководство пользователя | Manualshive

Страница: 14 / 64

background image

10

Detailed recommendations for the flue installations are given in BS 5440:1:2000. The following
notes are for general guidance only.
Note: An adapter is always required on top of the heater.

For the vertical flue set up, offset adapter will be supplied for the air intake.

a) The flue system must be constructed using only Powermax approved components.

b) It is important that the position of the terminal allows free passage of air across it at all times.

c) It is ESSENTIAL TO ENSURE that products of combustion discharging from the terminal

cannot reenter the building, or any other adjacent building, through ventilators, windows, doors,
other sources of natural air infiltration, or forced ventilation / air conditioning.

d) The minimum acceptable dimensions from the flue terminal to obstructions and ventilation

openings are specified in Figs. 4& 5 opposite.

e) If the flue terminal discharges into a pathway or passageway check that combustion products

will not cause nuisance and that the terminal will not obstruct the passageway.

a. Measure and cut the first pair of the flue pipes away from the appliance. Push pipes fully into

the sockets on top of the boiler whilst also fitting the flue duct prepared as above.

b. Measure and cut next pair of the air/flue pipes.

c. Prepare pipe support brackets as required before engaging pipes with the socket of preced-

ing pipes or bends.

d. Push pipes together as before taking care not to dislodge seals. When cutting and fitting the

flue pipes on extended the flue systems, allow approx. 5 mm clearance at the bottom of each
joint - see Fig. 8.

e. Repeat above procedure to reach terminal. Ensure that air inlet and the flue gas connections

are correctly made and are not inadvertently reversed.

f. Fix pipe supports to masonry or woodwork so that the flue/air pipes are held securely in

position.

g. Check especially that all joints within any duct or other void are correctly engaged and sealed

before fixing the ductwork.

The flue pipes must be assembled with the plain end of pipe or fitting nearest the boiler and the
female (socket) end furthest from the boiler. Check that a seal is fitted in every socket.

Always adjust length of pipes by cutting and de-burring plain end so that it does not damage or
disturb the seal. Remove burrs from inside and outside of pipe and ensure the pipe is clean and
free from oil and grease.

Any generally "horizontal" run of the flue pipe MUST NOT FORM A LOW POINT at which
condensate could accumulate.

Assembling Air/Flue Pipes

(L)WH42̲56(09̲15)̲E

05.9.28, 1:21 PM

Page 10

Adobe PageMaker 6.5J/PPC

«
...
12
13
14
15
16
...
»

Содержание LWH42

































































Отзывы:

Нет отзывов

Похожие инструкции для LWH42

Бренд: Yoshitake Страницы: 5

Бренд: Water Worker Страницы: 24

Бренд: Zoeller Страницы: 24

Бренд: ICMA Страницы: 2

Бренд: Gardena Страницы: 16

Бренд: Gardena Страницы: 9

Бренд: Gardena Страницы: 11

13000 aquasensor

Бренд: Gardena Страницы: 14

Бренд: TapFlo Страницы: 63

Бренд: AmeriWater Страницы: 16

Бренд: Prem-I-Air Страницы: 7

Бренд: Hellenbrand Страницы: 8

Бренд: Northern Radiator Страницы: 2

jumbo floodfighter

Бренд: Davey Страницы: 8

Бренд: IMO Страницы: 24

UFLEX SilverSteer UP25 F-SVS

Бренд: Ultraflex Страницы: 29

Бренд: ARDES Страницы: 28

EZH2O LZWS-LRPBM28K

Бренд: Elkay Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды