andrews LWH42 Скачать руководство пользователя

Страница: 32 / 64

1) Determine the flue terminal installation

location and make a 160 mm diameter hole.
Install the sleeve into the hole with the
triangular mark ( ) pointing up. Use the
wall anchors and rounded wood screws.

174

142

174

Screw holes (4)

(7.2 mm diameter and
35 to 40 mm depth).

Triangular mark ( )

Before installing the sleeve, adjust its length to fit
the wall thickness.
(The length can be adjusted in increments of 10 mm.)

Waterproof the clearance between the sleeve
and wall hole with a high temperature sealant.

2) Attach the wall flange to the sleeve.

Sleeve

Wall flange

Tapping screw

Terminal Orientation Flange Orientation

Outlet Orientation

(1)

The terminal cannot be installed in this
orientation.

Sleeve

Waterproof the
clearance with a high
temperature sealant.

Rounded wood screw (short)

Sleeve

Wall anchor

Waterproof the clearance with
a high temperature sealant.

Rounded wood
screw (long)

(2)

(4)

(3)

Down

Top

Bottom

Correct

Incorrect

Intake

Exhaust

Intake

Exhaust

Down

Intake

Exhaust

Intake

Exhaust

174 mm

210 mm

174 mm

210 mm

174 mm

210 mm

* The proper flange orientation

depends on the desired
orientation of the flue terminal.

* Unless the flue terminal is

installed as in option (1) in the
chart to the right, the outlet will
need to be adjusted in order to
ensure it is oriented in the proper
direction.

Remove this screw
and slide out the
external cylinder.

Slide out the external cylinder
until it is flush with the external
wall and replace screw.

160 mm dia.

15-1-4. Flue Terminal Installation Procedure

* When drilling, take care not to damage electric

wiring, or gas or water piping in walls.

(L)WH42̲56(25̲32)̲E

05.10.4, 1:35 PM

Содержание LWH42

































































Результаты поиска

Содержание LWH42

Отзывы:

Похожие инструкции для LWH42

Бренды по названию

Популярные бренды

andrews LWH42, Руководство по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание LWH42

Отзывы:

Похожие инструкции для LWH42

Бренды по названию

Популярные бренды