andrews LWH42 Скачать руководство пользователя

Страница: 33 / 64

3) Adjusting the flue terminal length

Make sure the flue terminal has been set to the appropriate length and the outlet is oriented
properly to prevent combustion and operation problems.

The length of the flue terminal must be
adjusted to fit with the wall thickness before
the installation is completed.

The sleeve length can be
adjusted in increments
of 10 mm.

<Screw positions>
The following figure shows the points to screw the
cylinder to for the different installation orientations.

Screwing position for
installation pattern (3)

4) Attach the flue terminal to the wall flange.

* Installation pattern (3) yields a clearance between the flue terminal and
the wall surface. Fill this clearance with a high temperature sealant.

Wall flange

Flue Terminal

Wing nut

The following figure shows installation pattern (1).

External wall surface

Standard projection
length: 75 mm

The red line should be visible.
The red rectangle should not be
visible from the outdoor.

Screwing position for
installation pattern (2)

Fill in clearance with
sealant

Note: If the flue terminal will be installed in

orientations (2) or (3) from the table on the
previous page, the outlet cylinder will have
to be rotated so that it is oriented properly.

Installation pattern (1),
as is with shipment

Wind packing along the red
rectangle only for wall thicknesses
of 370 mm to 690 mm.

Remove this screw and slide
out the external cylinder.

(L)WH42̲56(25̲32)̲E

05.10.4, 1:35 PM

Содержание LWH42

































































Результаты поиска

Содержание LWH42

Отзывы:

Похожие инструкции для LWH42

Бренды по названию

Популярные бренды

andrews LWH42, Руководство по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание LWH42

Отзывы:

Похожие инструкции для LWH42

Бренды по названию

Популярные бренды