AMX Modero NXD-1200V Скачать руководство пользователя

Страница: 26 / 176

Touch Panel Accessories

NXD/T-1200V Wall/Flush Mount Touch Panel

Product Specifications

NXA-PCI80211G Specifications

Dimensions (HWD):

• 0.02" x 2.13" x 4.66" (5.0 mm x 54.0 mm x 118.4 mm)

Weight:

• 1.05 oz (30g)

Description:

• Direct Sequence Spread Spectrum (DSSS)/CCK 802.11g Wireless mini-PCI card with

detachable antennas.

Features:

• Contains integrated power amplifier (PA) and low-noise amplifier (LNA)

• Diversity Antenna Connectors automatically select the best available signal

• Enhanced transmit and receive chains

• Field-installable

• Increased sensitivity and multipath tolerance

• Operates from 2.300-2.500 GHz

• Operate at ISM frequency bands (2.4GHz) with 54Mbps data rate

• Pre-configured to communicate with current AMX Wireless Access Points

• Support for IEEE 802.11b and 802.11g

• Wired Equivalent Privacy (WEP) 64-bit and 128-bit data encryption

Antenna Type:

• Dual antenna connector

Availability:

• All 1200V-Series and VG-Series NXT Table Top panels come factory configured for

wireless communication.

These NXT panels are all factory installed with both the NXA-

80211G wireless mini-PCI and 2 antennas.

• Optional to the following NXD panels:

- NXD-1200V
- NXD-1200VG
- NXD-1500VG
- NXD-1700VG

Bus Interface:

• mini-PCI card, TypeIIIB

Certifications:

• FCCID: CWU-WN2301A, CE, EN 60950, EN 300 328, and RSS 210and FCCID

(CWU-WN2301A)

Frequency Range:

• Using 802.11b & g communication:

- 2.412 ~ 2.462 GHz - North America
- 2.412 ~ 2.484 GHz - Japan
- 2.412 ~ 2.472 GHz - Europe ETSI
- 2.457 ~ 2.462 GHz - Spain
- 2.457 ~ 2.472 GHz - France

Media Access Technique:

• CSMA/CA with ACK

Modulation:

• Orthogonal Frequency Division Multiplexing (OFDM) / Complementary Code Keying

(CCK)

Network Architecture:

• Ad-hoc mode (Peer-to-Peer)

• Infrastructure mode

Network Standard:

• IEEE Compliant

• 802.11b and 802.11g

Operating Channels:

• Using 802.11b & g communication:

- 11: (Ch 1 - 11) - North America
- 14: (Ch 1 - 14) - Japan
- 13: (Ch 1 - 13) - Europe ETSI
- 2: (Ch 10 - 11) - Spain
- 4: (Ch 10 - 13) - France

Operating Environment:

• Temperature: 0°C ~ 55°C (32°F to 131°F) (operating) and

-20°C ~ 70°C (-4°F to 158°F) (storage)

• Humidity: (non-condensing) 5% ~ 90% RH (operating) and

(non-condensing) 5% ~ 95% RH (storage)

Operating Voltage:

• 3.3V + 5% I/O supply voltage

Содержание Modero NXD-1200V

















































































































































































Результаты поиска

Содержание Modero NXD-1200V

Отзывы:

Похожие инструкции для Modero NXD-1200V

Бренды по названию

Популярные бренды

AMX Modero NXD-1200V, Руководство по эксплуатации/справочник

Результаты поиска

Содержание Modero NXD-1200V

Отзывы:

Похожие инструкции для Modero NXD-1200V

Бренды по названию

Популярные бренды