AmeriGlide STRATOS VPL Скачать руководство пользователя страница 9

Страница: 9 / 44

STRATOS WITH ENCLOSURE:

Install Manual

25MAR2022 | 630-00147 C

PREPARATION

STRATOS WITH ENCLOSURE: SECTION 3

SECTION 3

PREPARATION

Installations may vary to some degree, but below

are the basic tools to have on hand for a Stratos with

Enclosure Platform Lift installation.

Depending on the height of the application, you may

need to use a scissor lift or crane.

If you have any questions, concerns or comments,

please contact our LiftSquad Support at

800-833-0478 or [email protected].

REQUIRED TOOLS AND

HARDWARE

•

Tape Measure

•

Grounding Strap

•

Square

•

Level

•

Multimeter

•

Wire Cutters, Wire Puller

•

Stripper, Crimping Tool

•

Hammer Drill

•

3/8

•

Wrench Set:

•

7/16

•

1/2

•

9/16

•

3/4

•

Allen Wrench:

•

1/8

•

3/16

•

5/16

•

Torx Wrench

•

T20

•

No. 1 Phillips Head Screwdriver

•

No. 2 Flat Head Screwdriver

•

No. 2 Phillips Head Screwdriver

•

Marking Implement

•

3/8" Nut Driver Bit (with 1.5" min reach) or 3/8"

socket, extension and ratchet

•

Concrete Drill Bits

•

Temporary Power Means

•

Precision Screwdriver Set

•

Yellow / 74B wire Nut

•

Anchors for Fixed Ramp

(if specified)

RECOMMENDED TOOLS

•

Work Lights (Wired or Wireless)

•

Fish Tape

•

Ladder

•

Steel Toe Shoes

•

Safety Glasses

•

First Aid Kit

•

Box Cutter

•

Hard Hat

•

Shop Vacuum

•

Shop Towels and General Purpose Cleaner

Содержание STRATOS VPL













































Результаты поиска

Содержание STRATOS VPL

Отзывы:

Бренды по названию

Популярные бренды

AmeriGlide STRATOS VPL, Инструкция по установке и обслуживанию

Результаты поиска

Содержание STRATOS VPL

Отзывы:

Бренды по названию

Популярные бренды