AmeriGlide STRATOS VPL Скачать руководство пользователя страница 4

Страница: 4 / 44

STRATOS WITH ENCLOSURE:

Install Manual

25MAR2022 | 630-00147 C

SAFETY

STRATOS WITH ENCLOSURE: SECTION 1

SECTION 1

SAFETY

SAFETY DEFINITIONS

This safety alert symbol appears with

safety statements. It means attention,

become alert, your safety and the

safety of others are involved! Please

read and abide by the message that

follows the safety alert symbol.

NOTE: Indicates a condition that should be followed in

order for the lift to function in the manner intended.

ENVIRONMENTAL

CONDITIONS

The technician shall assess the surrounding

conditions and verify that the location is acceptable

before performing installation and/or servicing

tasks. Installation shall not proceed in inclement

weather conditions that jeopardize the technician’s

safety or ability to complete the installation in a safe

manner. Tents, canopies or other outdoor provisions

that help protect the work area from weather or

other safety concerns are recommended when

conditions warrant.

If you do not understand any portion of the

installation or operation procedures, please consult

Ameriglide's Support at 866-378-6648.

Do not attempt to install or use this lift if you have

any hesitation or question. Serious injury or damage

can result if proper procedures are not followed.

Indicates a hazardous situation that, if not
avoided, could result in death or serious injury.

WARNING

Indicates a hazardous situation that, if not avoided,
could result in minor or moderate injury.

CAUTION

Indicates a situation which can cause damage to

the lift and/or the environment, or cause the lift to

operate improperly.

NOTICE

Содержание STRATOS VPL













































Результаты поиска

Содержание STRATOS VPL

Отзывы:

Бренды по названию

Популярные бренды

AmeriGlide STRATOS VPL, Инструкция по установке и обслуживанию

Результаты поиска

Содержание STRATOS VPL

Отзывы:

Бренды по названию

Популярные бренды