AmeriGlide STRATOS VPL Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 44

background image

STRATOS WITH ENCLOSURE:

Install Manual

25MAR2022 | 630-00147 C

14

INSTALLATION

STRATOS WITH ENCLOSURE: SECTION 4

SECTION 4

INSTALLATION

NO HOISTWAY / NO FLOOR

PENETRATION

1. Remove 5X front screws.

2. Remove the plastic top cap by loosening the

four (4) side screws and lifting the top cap.

This part will be replaced by the Stratos with

enclosure metal top cap. See Figure 4-1.

5X front

screws

4X side

screws

Figure 4-1

3. Remove the front panel by rotating it out

slightly and lifting it out of the lower slots.

4. Position the VPL tower close to the upper

landing and stand it up using appropriate

material handling processes.

NOTE: Tower frame should only be lifted by the

rectangular tubes below the top plate.

ELECTRICAL CONNECTION

Kill all power before making any electrical
connections.

WARNING

!

1. Remove and discard the temporary bolt and

nut (9/16" hex) that secures the tensioning

pulley to the carriage for shipping. This bolt is

indicated with a red tag. Suspend the pulley

assembly behind the carriage. See Figure 4-2.

Pulley

Assembly

Temporary

Shipping Bolt

Figure 4-2

NOTE: Be sure that the pulley assembly is suspended with

the sheeve at the top and that it is clear to move through

the lift range.

2. Connect the 8-pin platform control box

connector.

«
...
12
13
14
15
16
...
»

Содержание STRATOS VPL













































Отзывы:

Нет отзывов

Похожие инструкции для STRATOS VPL

Бренд: Hama Страницы: 10

Бренд: ZALMAN Страницы: 16

Бренд: Campbell Страницы: 28

Бренд: Mitsubishi Electric Страницы: 22

Бренд: Macpower & Tytech Страницы: 14

RocketStor 6418AS

Бренд: HighPoint Страницы: 4

RocketStor RS6124V

Бренд: HighPoint Страницы: 53

Бренд: ZALMAN Страницы: 2

Бренд: ZALMAN Страницы: 8

Бренд: Gumdrop Страницы: 2

Бренд: GAMDIAS Страницы: 14

Бренд: Icy Dock Страницы: 15

INTERFACE-TERMINAL

Бренд: OKW Страницы: 18

Бренд: Eaton Страницы: 7

US-S ESF30 Series

Бренд: Eaton Страницы: 20

SecureBack M Series

Бренд: Kensington Страницы: 8

Бренд: Pulsar Страницы: 4

DataSafe 307100

Бренд: DataStor Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды