American Dryer Corp. ML-175 Скачать руководство пользователя

Страница: 7 / 54

113406-1

www.amdry.com

7. A program

should be

established for the inspection and cleaning of lint in the burner area, exhaust ductwork,

and area around the back of the dryer. The frequency of inspection and cleaning can best be determined
from experience at each location.

WARNING:

The collection of lint in the burner area and exhaust ductwork can create a potential fire
hazard.

8. For personal safety, the dryer

must be

electrically grounded in accordance with local codes and/or the

National Electrical Code ANSI/NFPA NO. 70-LATEST EDITION, or in Canada, the Canadian Electrical
Codes Parts 1 & 2 CSA C22.1-1990 or LATEST EDITION.

NOTE:

Failure to electrically ground the dryer properly will VOID THE WARRANTY.

UNDER

CIRCUMSTANCES

should the dryer door switch, the lint drawer switch, or the heat

safety circuit ever be disabled.

WARNING: PERSONAL INJURY OR FIRE COULD RESULT SHOULD THE DRYER

DOOR SWITCH, THE LINT DRAWER SWITCH, OR THE HEAT SAFETY
CIRCUIT EVER BE DISABLED.

10. This dryer is not to be used in the presence of dry cleaning solvents or fumes.

11. Remove articles from the dryer as soon as the drying cycle has been completed.

WARNING:

Articles left in the dryer after the drying and cooling cycles have been completed can
create a fire hazard.

12.

DO NOT

operate steam dryers with more than 125 psi (8.62 bar) steam pressure. Excessive steam

pressure can damage the steam coil and/or harm personnel.

13. Replace leaking flexible steam hoses or other fixtures immediately.

DO NOT

operate the dryer with

leaking flexible hoses.

PERSONAL INJURY MAY RESULT.

14. READ AND FOLLOW ALL CAUTION AND DIRECTION LABELS ATTACHED TO THE DRYER.

15. For safety, proper operation, and optimum performance, the dryer

must not be

operated with a load less

than sixty-six percent (66%), 112 lbs (51 kg) of its rated capacity.

WARNING: YOU MUST DISCONNECT AND LOCKOUT THE ELECTRIC SUPPLY AND

THE GAS SUPPLY OR THE STEAM SUPPLY BEFORE ANY COVERS OR
GUARDS ARE REMOVED FROM THE MACHINE TO ALLOW ACCESS
FOR CLEANING, ADJUSTING, INSTALLATION, OR TESTING OF ANY
EQUIPMENT PER OSHA

(Occupational Safety and Health Administration)

STANDARDS.

IMPORTANT: Dryer must be installed in a location/environment, which the ambient

temperature remains between 40° F (4.44° C) and 130° F (54.44° C)

Содержание ML-175























































Результаты поиска

Содержание ML-175

Отзывы:

Похожие инструкции для ML-175

Бренды по названию

Популярные бренды

American Dryer Corp. ML-175, Руководство по установке

Результаты поиска

Содержание ML-175

Отзывы:

Похожие инструкции для ML-175

Бренды по названию

Популярные бренды