American Dryer Corp. ML-175 Скачать руководство пользователя | Manualshive

Страница: 30 / 54

background image

26

American Dryer Corp.

113406-1

4. Steam Damper Air System Connections

The dryer is manufactured with a pneumatic (piston) damper system, which requires an external supply of
compressed air. The air connection is made to the steam damper solenoid valve, which is located at the
rear inner top area of the dryer just in front of the electric service relay box. (Refer to the

bottom

illustration

on the next page.)

a. Air Requirements

Shaded areas are stated in metric equivalents

b. Air Connection

Air connection to system ______ 1/4” Quick Connection

c. No air regulator or filtration is provided with the dryer. External regulation/filtration of 80 psi (5.51 bar)

must be

provided. It is suggested that a regulator/filter gauge arrangement be added to the compressed

air line just before the dryer connection. This is necessary to ensure that correct and clean air pressure
is achieved.

5. Steam Damper System Operation

The steam damper as shown in the

top illustration

on the next page, allows the coil to stay constantly

charged eliminating repeated expansion and contraction. When the damper is opened, the air immediately
passes through the already hot coil, providing instant heat to start the drying process. When the damper is
closed, ambient air is drawn directly into the basket (tumbler), allowing a rapid cool down.

Diagram 1

shows the damper in the heating (open) mode, allowing heat into the basket (tumbler).

Diagram 2

shows the damper in the cool down (closed) mode, pulling ambient air directly into the basket

(tumbler) without passing through the coils.

NOTE:

With the dryer off or with no air supply, the steam damper is in cool down mode as shown in

Diagram 2

at the top of the next page.

Compressed Air Supply

Air Pressure

Normal

80 psi

5.51 bar

Minimum Supply

70 psi

4.82 bar

Maximum Supply

90 psi

6.20 bar

«
...
28
29
30
31
32
...
»

Содержание ML-175























































Отзывы:

Нет отзывов

Похожие инструкции для ML-175

Бренд: Quincy Compressor Страницы: 12

Бренд: Gorenje Страницы: 56

Бренд: san ignacio Страницы: 27

PRIMOTECQ TW730E

Бренд: FUST Страницы: 60

Бренд: exonda Страницы: 108

Roper RGL4634BL2

Бренд: Roper Страницы: 57

MAXX PLUS FT 47822 SS MAXX PLUS FT 47824 SS MAXX PLUS FT 50876 SS

Бренд: Kalorik Страницы: 40

Бренд: ELEKTRA Страницы: 56

EASY FRY GRILL DIGITAL

Бренд: T-Fal Страницы: 21

Бренд: Sinbo Страницы: 20

Бренд: GE Страницы: 32

Бренд: GE Страницы: 40

Бренд: GE Страницы: 128

Бренд: GE Страницы: 16

Бренд: GE Страницы: 32

Бренд: GE Страницы: 40

Бренд: GE Страницы: 40

Бренд: GE Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды