American Dryer Corp. ML-175 Скачать руководство пользователя | Manualshive

Страница: 34 / 54

background image

30

American Dryer Corp.

113406-1

IMPORTANT:

There is no regulator provided in a liquid propane (L.P.) dryer. The water column
(W.C.) pressure

must be

regulated at the source (L.P. tank) or an external regulator

must be

added to each dryer.

b. Steam Models

Check to ensure that the steam damper is functioning properly.

The steam damper should not “slam” (open or closed) when it reaches the end of (piston) travel.
Additionally, the steam damper should not bind and/or stop during travel. If either of these conditions
occur, the flow control

must be

adjusted. Refer to the

bottom illustration

on

page 27

for air adjustment

instructions.

6. Make a complete operational check of

ALL

safety-related circuits (i.e., lint drawer switch and sail switch

on gas models).

NOTE:

To check for proper sail switch operation, open the main door and while holding main door
switch plunger in, start the dryer. The dryer should start but the heat circuit

should not be

activated (on). If the heat (burner) does activate, shut the dryer off and make the necessary
adjustments.

7. Reversing basket (tumbler) dryers

must never be

operated with less than a 112 lb (51 kg) load (dry

weight), since the load’s weight affects basket (tumbler) coast time during a direction reversal command.
It is important that the basket (tumbler) come to a complete stop prior to starting in opposite direction.

Microprocessor Controller (Computer) Dryer Models

a. Spin and dwell (stop) times are not adjustable in the Automatic Mode and have been preprogrammed

into the microprocessor controller (computer) for 150-seconds spin time in the forward direction and
120-seconds in the reverse direction with a 5-second dwell (stop) time.

b. Spin and dwell (stop) times are adjustable in the Manual (Timed) Mode.

BASKET (TUMBLER) COATING

The basket (tumbler) is treated with a protective coating. We suggest dampening old garments or cloth material
with a solution of water and nonflammable mild detergent and tumbling them in the basket (tumbler) to remove
this coating.

8. Each dryer

should be

operated through one (1) complete cycle to ensure that no further adjustments are

necessary and that

ALL

components are functioning properly.

9. Make a complete operational check of

ALL

operating controls.

Microprocessor Controller (Computer) Programs/Selections:

Each microprocessor controller (computer) has been preprogrammed by the factory with the most commonly
used parameter (program) selections. If computer changes are required, refer to the computer programming
manual, which was shipped with the dryer.

«
...
32
33
34
35
36
...
»

Содержание ML-175























































Отзывы:

Нет отзывов

Похожие инструкции для ML-175

Essentials KDF250

Бренд: Kambrook Страницы: 6

Бренд: Amos Страницы: 8

Бренд: Amos Страницы: 11

Бренд: UFESA Страницы: 42

Бренд: Coline Страницы: 12

Бренд: Kasanova Страницы: 50

Бренд: Creda Страницы: 6

Бренд: Hottek Страницы: 18

Бренд: Parker Страницы: 162

Бренд: e-Ware Страницы: 9

Бренд: Kalorik Страницы: 40

Бренд: Electrolux Страницы: 48

Бренд: Electrolux Страницы: 76

Бренд: Electrolux Страницы: 80

Бренд: Electrolux Страницы: 48

Бренд: Electrolux Страницы: 240

Бренд: Electrolux Страницы: 68

CATERINA 746033

Бренд: Stalgast Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды