American Dryer Corp. ML-175 Скачать руководство пользователя | Manualshive

Страница: 19 / 54

background image

113406-1

www.amdry.com

15

The ductwork

should be

smooth inside with no projections from sheet metal screws or other obstructions,

which will collect lint. When adding ducts, the duct to be added should overlap the duct to which it is to be
connected.

ALL

ductwork joints

must be

taped to prevent moisture and lint from escaping into the

building. Inspection doors

should be

installed at strategic points in the exhaust ductwork for periodic

inspection and cleaning of lint from the ductwork.

NOTE:

When the exhaust ductwork passes through a wall, ceiling, or roof made of combustible
materials, the opening

must be

2-inches (5.08 cm) larger than the duct (all the way around).

The duct

must be

centered within this duct.

Outside Ductwork Protection

To protect the outside end of the horizontal ductwork from the weather, a 90° elbow bent downward

should be

installed where the exhaust exits the building. If the exhaust ductwork travels vertically up

through the roof, it

should be

protected from the weather by using a 180° turn to point the opening

downward. In either case, allow at least twice the diameter of the duct between the duct opening and the
nearest obstruction.

IMPORTANT: DO NOT

use screens, louvers, or caps on the outside opening of the exhaust

ductwork.

«
...
17
18
19
20
21
...
»

Содержание ML-175























































Отзывы:

Нет отзывов

Похожие инструкции для ML-175

Бренд: Coline Страницы: 12

Бренд: Maytag Страницы: 5

Бренд: Parker Страницы: 100

Бренд: Salton Страницы: 10

SilverLine SLE40

Бренд: Anetsberger Brothers Страницы: 2

Бренд: Blue Dry Страницы: 5

Бренд: Alpine Страницы: 11

Бренд: GE Страницы: 32

Бренд: GE Страницы: 44

Бренд: GE Страницы: 111

Бренд: GE Страницы: 16

Бренд: GE Страницы: 32

Бренд: GE Страницы: 40

Бренд: GE Страницы: 40

Бренд: GE Страницы: 40

Бренд: GE Страницы: 32

Бренд: Blue Seal Страницы: 40

Бренд: Wise Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды