American Dryer Corp. ML-175 Скачать руководство пользователя | Manualshive

Страница: 23 / 54

background image

113406-1

www.amdry.com

19

The neutral will only be used on 4-wire service. This is typical for 380-416V, 50 Hz.

CAUTION:

The dryer

must be

grounded. A ground lug has been provided for this purpose.

Input connection wiring

must be

sized properly to handle

the dryer’s current draw. This information is printed on
the dryer’s data label.

The electrical input connections are made at the electric
oven contactor located inside the assembly at the rear
center upper section of the dryer. The ground connection
is made to a copper lug also provided in this area. To
gain access, remove oven rear service cover.

IMPORTANT:

A strain relief

must be

used where the

input wiring enters the oven assembly.

4. Electrical Connections

A wiring diagram is located inside the control box for connection data.

If local codes permit, power to the dryer can be made by the use of a flexible U.L. listed power cord/pigtail
(wire size

must conform

to rating of dryer), or the dryer can be hard wired directly to the service breaker

panel. In both cases, a strain relief

must be

installed where the wiring enters the dryer.

IMPORTANT:

A separate protected circuit

must be

provided to each dryer.

3-Phase (3ø) Wiring Connections/Hookup

The electrical connections on

ALL

3-phase (3ø) gas and steam dryers are made into the rear service box

located at the lower left area of the dryer. The electrical connections are made at the power distribution
block located in the service box. The ground connection is made to the copper lug, also provided in this box.
To gain access, the service box cover

must be

removed.

«
...
21
22
23
24
25
...
»

Содержание ML-175























































Отзывы:

Нет отзывов

Похожие инструкции для ML-175

Pro Digital 6000E

Бренд: BaByliss Страницы: 2

Бренд: BaByliss Страницы: 53

Бренд: BaByliss PRO Страницы: 24

Beliss IoniCeramic 5712E

Бренд: BaByliss Страницы: 19

Бренд: Breville Страницы: 7

Бренд: Premier Страницы: 7

Бренд: Conair Страницы: 2

Бренд: Domus Страницы: 114

Бренд: Gaggenau Страницы: 52

Бренд: TSM Страницы: 102

Бренд: Starmix Страницы: 140

Бренд: Haden Страницы: 18

Бренд: baridi Страницы: 10

Бренд: Hotpoint Страницы: 16

Бренд: Slinger Страницы: 8

LAVATHERM 76781IH1

Бренд: AEG Страницы: 24

LAVATHERM 8DEC946S

Бренд: AEG Страницы: 28

Бренд: Miele Страницы: 100

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды