American Dryer Corp. ML-175 Скачать руководство пользователя | Manualshive

Страница: 41 / 54

background image

113406-1

www.amdry.com

37

STEAM DRYERS

Clean the steam coil fins. Suggest using compressed air and a vacuum cleaner with brush attachment.

NOTE:

When cleaning steam coil fins, be careful not to bend the fins. If fins are bent, straighten by
using a fin comb, which is available from any local air conditioning supply house.

90 DAYS

Remove lint from around basket (tumbler), drive motors, and surrounding areas. Remove lint from the gas valve
burner area with a dusting brush or vacuum cleaner attachment.

Impellor (fan/blower) shaft bearings

should be

lubricated using Shell Alvania grease NLGI 2 or its equivalent.

Generically, this grease would be described as an NLGI grade 2 multipurpose industrial grease with a lithium
thickener and mineral base oil.

Check to make sure that the setscrews on the impellor/fan shaft bearings are tight.

NOTE:

To prevent damage, avoid cleaning and/or touching the Direct Spark Ignitor.

Remove lint accumulation from inside.

6 MONTHS

Inspect and remove lint accumulation in customer furnished exhaust ductwork system and from dryer’s internal
exhaust ducting.

NOTE: THE ACCUMULATION OF LINT IN THE EXHAUST DUCTWORK CAN

CREATE A POTENTIAL FIRE HAZARD.

NOTE: DO NOT

OBSTRUCT THE FLOW OF COMBUSTION AND VENTILATION AIR.

CHECK CUSTOMER FURNISHED BACK DRAFT DAMPERS IN THE EXHAUST
DUCTWORK. INSPECT AND REMOVE ANY LINT ACCUMULATION, WHICH
CAN CAUSE THE DAMPER TO BIND OR STICK.

NOTE:

A back draft damper that is sticking partially closed can result in slow drying and shut down of
the heat circuit safety switches or thermostats.

NOTE:

When cleaning the dryer cabinet(s), avoid using harsh abrasives. A product intended for the
cleaning of appliances is recommended.

Check

ALL

V-belts for tightness and wear. Retighten, realign, or replace if required.

NOTE:

V-belts

should be

replaced in matched sets (pairs).

«
...
39
40
41
42
43
...
»

Содержание ML-175























































Отзывы:

Нет отзывов

Похожие инструкции для ML-175

Bear Power Pro Series

Бренд: B-Air Страницы: 5

Бренд: Asko Страницы: 24

Бренд: Midea Страницы: 104

Бренд: Hoover Страницы: 36

Бренд: nedis Страницы: 108

AirFryer Pro Plus CM003

Бренд: Power Страницы: 20

Бренд: Amana Страницы: 20

Бренд: Felix Storch Страницы: 35

Бренд: Frymaster Страницы: 24

01.182026.01.001

Бренд: Princess Страницы: 66

Бренд: Speed Queen Страницы: 4

Classic FP5500P

Бренд: Sunbeam Страницы: 36

Бренд: Frigidaire Страницы: 16

Бренд: Frigidaire Страницы: 3

Бренд: Frigidaire Страницы: 22

Бренд: Frigidaire Страницы: 18

Бренд: Frigidaire Страницы: 39

Бренд: Frigidaire Страницы: 51

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды